12
9. EXPLODED VIEW AND SPARE PART LIST
lrregularity Measures
1. In the event the pruning shear is not able to cut through an object, released the trigger immediate-
ly and the moving blade will return to its open position automatically.
2. In the event the pruning shear is cutting through a branch of particularly hardness,released the
trigger immediately and the moving blade will return to it´s open position automatically.
3. In the event the battery is not charging properly, please check if the charger is the one provided
with the package during purchase. Next is to ensure the supply voltage to the charger is same rating
as the specificatlon of the charger.
4. In the event of electric or mechanical malfunction, power OFF immedialely.
5. Operating not following instructions in this manual may result battery fluid leakage, do not con-
tact the leaked batlery fluid. In the event of accidental contact with battery fluid, clean with clear
water immediately. lf the battery fluid keeps in contact with the eyes, wash wilh clear water and
must seek hospital assistance. Fluid from leaked battery may causad irritations or burns.
After sale service
Should you have any questions regarding the pruning shears, please contact us immediately (con-
tact information is on the cover). Our professionals will resolve the problems for you, and our quali-
fied engineers will repair your electric pruning shears.
Disclaimer
Our company reserves the right to make any design and manufacturing changes deemed necessary
to improve on the performance. Thank you your understanding. If there are differences between the
physical tool and the graphics as well as texts in this manual, take the physical item as the most
accurate.
of battery.
14. Do not connect the battery to charging outlets or car cigarette lighter socket.
15. Do not use the battery on equipment other !han the designated pruning shear.
16. Do not dlrect contact wlth llthlum cells In the battery.
17. Do not place the battery in microwave, high temperatura or high pressured vessel.
18. Do not use the battery that is leaking.
19. Keep the battery out of reach from CHILDREN.
20. Do not use or place the battery under direct sunlight (or in vehicle that are under direct sunlight)
that will cause the battery to overheat or bum shortening the battery lifespan.
21. Do not use the battery in electrostatic environment(above 64V).
22. Do not usebattery that is corroded, with unpleasant odor or unusual appearance.
23. lf the skin or clothing comes into direct contact with battery fluid, wash with clearwater imme-
diately.
24. Maintain the battery fully charged when the pruning shear is not used and electricity is charged
every three months for a long period of time.
8. SAFETY NOTES
WARNING!
Please read all instructions carefully,not complying with instruction may lead to electric
shocks,fire or other serious damage.
Workplace safety
1. Keep work area clean and bright , messy and dimmed workplace may cause accidents.
2. Do not use the pruning shear in explosive , inflammable or hum id environment.
3. Keep CHILDREN and bystander away before operating the pruning shear to avoid accidental
injury due to distraction.
Electrical safety
1. Pruning shear battery socket must be compatible with the power cable plug, do not modify the
socket and plug.
2. Do not exposed the pruning shear to rain, humid environment, water or any other moisture that
will risk electrical shock.
3. Do not misuse the power cord. Do not lift or pull the pruning shear by !he power cord. Keep the
pruning shears away from heat, oil, sharp edges or moving parts.
Human safety
1. Keep alert while using the pruning shear. Do not operate the pruning shear when you are tired or
under the influence of drugs or alcohol.
2. Use protective devices, always wear safety goggles as well as other safety tools such as dust
mask, anti-slide boots, helmet and hearing protective devices that will reduce the risk of injury.
3. Before powering on the pruning shear ensure all adjusting tools and spanners are removed. Tools
left on the rotating parts of pruning shear may result injury.
4. Do not over stretch hands when operating the pruning shear, keep both hands from cutting area.
Do not under any circumstances place !he hands beneath the branches, al the same ensure the
surface and underside of the branches do not have any material that can be damage by cutting
edges. Always mainlain balance and in control of pruning shear in any situation.
5. Dress appropriately, do not wear loase clothing or jewelry. Keep hair, clothing and sleeves away
from the pruning shear. Loase clothing, accessories and long hair may be enlangled with the moving
parts of the tool.
Fixed and movable blades can be re placed individually; do not worry about the size of the replace-
ment blade aperture, the opening will automatically return to normal size during power ON after
completing blade replacement.
7. OPERATION PRECAUTIONS
Usage and care for pruning shear
1. Do not cut branches beyond the specified diameter indicated, do not cut hard items such as
metals,stone or any other non-plant materials. lf the bladesare worn or damaged, please replace the
blades.
2. Keep the pruning shear clean, use a clean cloth to clean the pruning shear, battery and charger
(do not use ant abrasive or solvent-based cleaningagent), use a soft brush or a dry to clean the dust
offthe pruning shear head.
3. Do not immerse the pruning shear, battery or charger in any liquid.
4. Follow instructions as given for proper use of the pruning shear, do not use the pruning shear
when the tool itself,battery or charger is damaged.
5. Do not use the pruning shear if it could not operate or shut down properly, send for servicing
immediately. lt is dangerous to use the pruning shearwhen the tool could not operate or shut down
properly.
6. Please ensure the power pruner is powered OFF during any adjustment, changing accessories or
storage. This protective meas u re aims to reduce the risk of accidental pruning shear activation.
7. Please ensure the blades are closed when not in use, remove the battery, storage of the pruning
shearmust keep out of reach from children, do notallow any person who is not familiar with the
pruner operation or instructionto use the pruning shear, it is dangerous to use the pruning shear
without proper training and understanding.
8. The use of the pruning shear must comply with instructions stated in this manual and methods of
use as well as taking in considerations of the workingenvironment and nature of work undertaken,
The use of the pruning shear notwithin its stated capability and specifications is dangerous.
9. Remove all dirt from the moving and fixed blades alter each use, thereafter apply lubricanton the
blade side where both moving and fixed blade contact. This will ensure the blades are maintained in
good conditions and reduceresistance during use prolonging the pruner and blade lifespan.
Usage and care for battery
1. Do not charge battery with ambient temperature below 32ºF (OºC) or above 113ºF (45ºC).
2. Please ensure the battery is switched off befo re connecting the power cord to the battery.
3. Only use battery charger as supplied together with the pruning shear, the use of any other char-
ger not matching to the charging specification of the battery may cause fire.
4. ltems such as paper clips, coins, keys, nails, screws, or any other conductive items must be keep
away from battery when not in use.
5. Do not disassemble the battery.
6. Do not short-circuit the battery.
7. Do not use the battery beside heat source.
8. Do not put the battery in fire or in water.
9. Do not charge the battery near fire or under direct sunlight.
10. Do not insert nail into the battery, hammer the battery, stomp the battery, throw the battery or
any other form of shocks to the battery.
11. Do not use battery that is damaged or deformed.
12. Do not perform soldering or welding on the battery.
13. Do not reverse direction of charging battery, reverse polarity of connections excessive discharge
Cautions
1. Before charging, please ensure battery power switch is in OFF position. During charging, it is
normal far the charger and battery to be warm.
2. lf the battery is not use for a long period of time, it recommended to charge the battery once
every 3 months, this is to ensure the battery life is not affected by low usage.
3. For new battery or battery unused far a long time,i t will need about 5 charge-discharge cycles
before achieving full capacity.
4. Do not recharge a fully charged battery just alter a few minutes of usage, this will reduce the
battery lifespan and efficiency.
5. Do not use a damaged battery and do not disassemble the charge ar battery.
6. Do not place battery near high temperatura heat source, the ballery will explode in fire ar long
exposure to high temperatura heat source.
7. Do not charge the battery in outdoor ar humid environment.
8. lt is normal for the pruning shear to reduce cutting diameter when the battery capacity is getting
low.
9. Do not use the pruning shear during charging. lt must be disconnected from the battery during
charging.
10. Do not store the battery in a humid environment.
Blade replacement
When the moving blade no longer crosses the fixed blade throughout ils length, or when the power
pruner could no longer have a clean cut after grinding, blade replacement is recommended with the
following steps:
1. For safety, before replacing the blade, please ensure the pruning shear is power OFF and power
cable disconnected from the battery.
2. Refer to the diagrams below on the procedure to replace the blade.
3. Clean up the the blade after replacing,connect to power cable to battery, power ON to test the
blade, close up the blade to complete the whole procedure.
4. TECHNICAL SPECIFICATIONS
Model:
DAWS-032
Model:
DAWS-032SG
Driver:
Gear
Driver:
Gear
Cut diameter: up to 30 mm
Cut diameter: up to 32 mm
Power: 16.8 V DC Brushless
Power: 16.8 V DC Brushless
Motor speed: 2300 rpm
Motor speed: 2300 rpm
Lithium battery: 2.6 Ah
Lithium battery: 4.5 Ah
Charger voltage: AC 110-240 V
Charger voltage: AC 110-240 V
Charging time: 2 hours
Charging time: 2 hours
Material of blade: Stainless alloy
Material of blade: Stainless alloy
Protect system: Yes
Protect system: Yes
Includes: Tool kit, BMC case, 2 batteries and power indicator.
Please read through all safety warnings and instructions carefully.
Failure to follow warnings and instructions may result in electric shock, fire and
serious burns and other accidents.
Do not use or exposed electric pruning shear in rainy conditions.
Never place hands near the cutting area of the electric pruning shear during operations.
Never contact charged objects with electric scissors.
5. DESCRIPTION PART
1. Movable blade
2. Fixed blade
3. Latch pin
4. Trigger
5. Power switch
6. Lubrication hole
7. Electric pruning shear´s power input connector
8. LED light indicator
9. Charging jack
10. Release button
11. Battery input connector
12. Battery output connector
6. PRODUCT OPERATION
Setting up
1. Open the package, insert the the baltery into the power connector of the pruner with designated
direction, see
.
2. Press the power button till the LED display indicator change to green. After the sound "Di- Di Di
Di" indicate that is activated. Double click the trigger, the pruner blades will automatically open.
3. Normal Pruning: Press trigger to clase the blades and release the trigger to open blades.
4. Press trigger for one second. Release trigger after hear the sound "Di Di" to adjust the size the
cut diameter. Conversion between large and small cut diameter can be achieved by the same opera-
tion.
5. Press trigger with one second after the sound "Di Di", for another 1.5 seconds press with the
sound " Di Di" The pruner comes into standby mode of (children's lock function). The pruner can
only be reopened with double click the trigger.
6. Pressing the trigger constently for 6 seconds, the notice sound will be heard "Di Di" "Di Di" "Di".
Release trigger, the function of blade injury prevention can be turned on or turned off. Please note
that the safety systerm is only auxiliary fuction, when the environment is very dry, the safety system
may fail.
7. Without operation for 3 minutes when the blades open, after sound 'Di Di" the pruner comes into
standby mode of (children's lock function), can only be reopened with double click the trigger.
Another without operation for 10 minutes, after sound " Di Di Di Di" the pruner automatic shutdown.
When the blades closed and pruner comes into standby mode of (children's lock function), without
operation for 10 minutes, after sound "Di Di Di Di" the pruner automatic shutdown.
8. Before operation, in order to see if the pruner and battery performances well, please press the
trigger to close and release the trigger to open the blades without cutting anything, repeat this for a
few times.
9. Start working after all normal.
Packing up
1. Press the trigger and hold far a few seconds and then release, the blade will clase and will not
open.
2. Switch off the battery, disconnect the battery.
3. Tidy up, clean up and pack the pruner into the tool box.
Failure tips
Battery charging
The battery connected to the charger. The charger plug connected to the power socket.
The LED indicator on the battery will turn RED during charging and turn GREEN when the battery is
fully charged.
1. PACKING LIST
lncluded in the case
1. Electric pruning shear
2. Lithium battery
3. Battery charger
4. Tool kit
2. SAFETY MARKS
NOTE
1. Please read through the manual carefully.
2. Battery can only be charged indoors.
3. Double insulation,grounding not required.
4. Fail-safe transformer charger.
5. Battery charging will automatically cut off when overheating occurs.
6. Dispose battery charger separately from house hold waste.
7. Dispose battery separately from household waste.
3. PRODUCT DESCRIPTION
This product is a battery-driven electric pruning shear,comprises a fixed blade, a movable blade,
lithium battery, battery charger, work vest, tool box and other components. Designed fir cutting or
trimming 1-25 mm or less branches in fruit orchards, vineyyards, etc. Simple and easy to operate, it
also has 8-10 times the efficiency of traditional manual pruners. Pruning quality is significantly
higher as compared to manual pruners.
1. Hexangular screw inside the head M6X20 - x1
2. Hexagon head flange face bolt M4x6 - x1
3.Hexagon nut M8 - x1
4. Double tooth face gasket 6 - x1
5. Backstop gear pad - x1
6. Trigger board - x1
7. Pin 6X10 - x1
8. Down blade - x1
9. Up blade - x1
10. Balance wheel-0.22
（
with Part No.40 together ,can not sell separately) - x1
11. Thrust roller bearing 889008 - x1
12. Screw for blade
（
with Part No. 13.12.11.5.3 together,can not sell separately) - x1
13. Oil cup 6 - x1
14. Outside the ring gear - x1
15. Gear mat - x1
16. Gear 18X0.5 - x3
17. Planet carrier 1 - x1
18. Gear 16 - x8
19. Planet carrier 2 - x1
20. Output planetary shelf - x1
21. Hole with elastic retainer type A 20 - x1
22. Deep groove ball bearing 619/9-2Z - x3
23. Cone gear 10+0.22 - x1
24. Box - x1
25. Plastic button 0929
（
with Part No.26 together,can not sell separately) - x1
26. Plastic button sticker - x1
27. Spring 4 - x1
28. Plastic switch - x1
29. Copper switch 0426 - x1
30. Left cover 0531 - x1
31. 18 motor - x1
32. Cross recess pan head screw
（
with Part No.31 together,can not sell separately) - x3
33. Battery 2.6 Ah - x1
34. Right cover 0531 - x1
35. Small cover 0601 - x1
36. Self-tapping screw - type C ST2.2X13 - x8
37. Self-tapping screw - type C ST2.2X16 - x2
38. Trident battery buckle - x1
39. Controller board
（
With Part No.38 together,can not sell separately) - x1
40. Steel magnet - x1
51. Box Assy - x1 set
52. Reduction Assy- x1 set
53. Switch Assy- x1 set
54. Gear Assy- x1 set
55. Charger- x1 set
