background image

3

Planning the Installation

 

WARNING

• 

IMPORTANT:

 Observe all governing codes and ordinances 

during planning and installation. Contact your local building 

department for further information.

•  To prevent an electric shock hazard, the power supply 

must meet the specifications stated below. It is the owner’s 

responsibility to make sure that the electrical service meets 

electrical requirements and that the electrical outlet has 

been properly installed by a licensed electrician.

The appliance installation must be electrically grounded in 

accordance with local codes or, in the absence of local codes, 

with the National Electrical Code, ANSI/ NFPA 70:

Electrical Requirements

• 

The range is supplied with a factory installed, 6 foot long, 

power cord with a three-prong grounding plug. It is connected 

to the chassis at the rear of the range. It must be connected 

to a dedicated, grounded three-prong electrical outlet.

• 

The correct voltage, frequency and amperage must be 

supplied to the appliance from a separate, grounded, circuit 

that is protected by a properly sized circuit breaker or time 

delay fuse.

Model

Circuit Required

Total 

Connected 

Load*

RNRP36G

120 Vac, 60 Hz, 15 Amp.

120 Vac 60 Hz, 

5.0 Amp.

RNRP48G

120 Vac, 60 Hz, 15 Amp.

120 Vac 60 Hz, 

8.0 Amp.

*These specifications for reference only. Refer to the rating label 

for exact specifications (see below for location).

Gas Supply Requirements

• 

The installation of this appliance must conform with local 

codes or, in the absence of local codes, with the National 

Fuel Gas Code, ANSI Z223.1/NFPA 54.

• 

Be certain that the appliance being installed is correct for 

the gas service provided (natural gas or LP gas). Also, if 

operating the range at an altitude above 4000 ft. (1219 m) 

make sure it is equipped for high altitude operation. Refer 

to the range rating label and the table on the inside cover to 

determine the correct model.

• 

See the table below for gas supply pressure requirements.

• 

The range comes from the factory with the regulator 

installed. Use only the installed regulator. The regulator inlet 

accommodates a 3/4” gas line. The range ships with a 1/2” to 

3/4” adapter connected to the regulator.

GAS SUPPLY PRESSURE REQUIREMENTS*

Gas Type

Minimum  

Manifold Pressure

Minimum Gas 

Supply Pressure**

Natural Gas

5” Water Column

6” Water Column

Liquid Propane (LP) 10” Water Column

11” Water Column

* The gas supply pressure for testing the regulator setting shall 

be at least 1 inch water column (249 Pa) above the specified 

manifold pressure.
** Maximum gas supply pressure for all models: 1/2 psi.
The ratings above are for reference only. Refer to the rating label 

for exact specifications (see below left for location).

B

A

Power 

cord

Gas 

Inlet

GAS - ELECTRICAL ACCESS DIMENSIONS

Model

A

B

RNRP36G

13 1/16” to 14 3/8” 

(33.2  to 36.5 cm)

7 5/16”  

(18.6 cm)

RNRP48G

13 1/16” to 14 3/8” 

(33.2  to 36.5 cm)

4 1/4”  

(10.8 cm)

Specifications Label Location

View rating label through slot on 

top of kick panel through opening 

between door and range

Содержание Renaissance RNRP36G

















Отзывы: