10
Starting Your Dishwasher
important
If the dishwasher drain line is connected to
a garbage disposal, run the disposal before
operating the dishwasher for proper drainage.
1.
Open the door and hold your finger
on the main power touch key until
the control panel lights.
2. Touch the
PROGRAM
key
repeatedly until the symbol for the desired wash
cycle appears on the display. See the facing
page for a description of the wash cycles.
NOTE:
The estimated wash time will also appear.
3. If you want to change the wash
temperature setting, touch the
Wash
Temperature
key repeatedly to
toggle between the “normal” setting
and the “high” setting. The light below the
Wash
Temperature
key is lit when the temperature
is set to “high.” See the facing page for a
description of the temperature settings.
4. If you want to change the dish drying
time, touch
Dry
repeatedly to toggle
between the “normal” and “high”
setting. The light below the
Dry
cycle key is lit when the dry time is set to “high.”
NOTE
: When set to “normal”, the rinse water
temperature is lower, causing the dishes to take
longer to dry. Change the setting to “high” if the
dishes do not dry properly.
NOTE:
This option is
not available for the
Rinse and Dry
and
Rinse
and Hold
cycles.
5. If you want to delay the start of
the dishwasher, touch
Delay Start
repeatedly to set the delay time on
the display (in hours). You can select
a delay of up to 24 hours.
NOTE:
Odd numbered
hours above 10 are not programmable.
6.
To start, hold your finger on the
START/STOP
key. The display will flash three times, then the
door open symbol will appear
on the display, indicating that
the dishwasher is ready to
start. Touching
START/STOP
for more than three seconds
a second time will cancel the
delay start option (if it was selected), but the
selected cycle will still run.
7. Close the door and push in gently on the top
until it clicks shut. If the door is not closed within
two minutes, the display will return to the cycle
setting that was run previously.
Operating Your Dishwasher
During Operation
•
During the cycle, the dishwasher’s computer
monitors the amount of soil left on the dishes
(by monitoring amount of soil in the water). The
amount of time required for the cycle to complete
varies based on the amount of soil left on the
dishes and the water temperature.
•
If power to the dishwasher is turned off at the
main power switch or if there is a power outage
before the wash cycle completes, the selected
cycle will continue when the power is restored.
However, if power is interrupted or the door is
open more than two minutes during drying, the
cycle will end.
Standby Mode
Once the cycle is finished, the dishwasher will beep
and
End
will appear on the display. When the cycle
completes the dishwasher draws a very small amount
of power. Open the door and hold your finger on the
main power key to turn power off completely.
Saving on Water and Energy Costs
•
To save energy, wait to run the wash cycle until
the dishwasher is full.
•
Use the
Rinse and Hold
cycle to rinse the
dishes if there are any unpleasant odors while
you wait for the dishwasher to become fully
loaded.
•
If the dishes are only lightly soiled, use the
normal temperature and/or dry setting. For best
results after the normal dry cycle, leave the door
open slightly after the end of the cycle.
•
Do not rinse dishes under running water. Simply
scrape off large food particles before loading.
Adding a Dish After You Start
You can add a dish, if needed, after starting your
dishwasher. Dacor recommends that you only add
items during the first five minutes of operation to
make sure they get clean.
To add a dish:
1. Slowly open the door. The dishwasher will stop
operating. Wait a moment for the steam to clear.
2. Without touching any of the hot surfaces or
racks, insert the item into one of the racks,
following the normal loading instructions.
3. Close the door. Push on the door handle to make
sure that the door is completely shut. Operation
will resume.
Door open
symbol
Содержание RDW24
Страница 2: ...2011 Dacor all rights reserved...