background image

29

MMD24S
MMD24B

2. 

Open the drawer and keep it open.

3.  To  discharge  the  high  voltage  capacitor,  wait  for  60 

seconds. 

4.  Remove the screw holding the latch hook to the oven 

flange.

5.  Remove the latch hook from the oven flange.
6.  Disconnect the wire leads of each switch.
7.  Remove each switch from the latch hook by pushing the 

one () stopper tab holding each switch.

8.  Now, each switch is free.

Re-install
.  Re-install each switch in its place. The secondary interlock 

switch is in the lower position and the monitor switch is 

STOP SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL

.  Follow the Microwave Drawer disassembly as previously stated 

in the top position, located on the left side of the unit. 
The door sensing switch by itself on the right side of the 
unit.

2.  Re-connect wire leads to each switch. Refer to pictorial 

diagram.

3.  Secure the latch hooks with mounting screws to oven 

flange.

4.  Make sure that the monitor switch is operating properly 

and check continuity of the monitor circuit.    Refer to 
chapter "Test Procedure" and "Adjustment procedure".

.  Follow the Microwave Drawer disassembly as previously 

stated 

2. 

Open the drawer and keep it open.

3.  To  discharge  the  high  voltage  capacitor,  wait  for  60 

seconds. 

4.  If the door sensing switch, secondary interlock switch 

and  monitor  switch  do  not  operate  properly  due  to  a 
misadjustment,  the  following  adjustment  should  be 
made.

6.  Loosen the screw holding latch hook to the oven cavity 

flange.

7.  With drawer closed, adjust latch hook by moving it back 

and forth, and up and down. In and out play of the door 
allowed by the upper and lower position of the latch hook 
should be less than 0.5mm. The vertical position of the 
latch  hook  should  be  adjusted  so  that  the  secondary 
interlock switch is activated with the drawer closed. The 
horizontal position of the latch hook should be adjusted 
so  that  the  monitor  switch  and  drawer  sensing  switch 
are activated with the drawer closed.

8.  Secure the screws with washers firmly.
9.  Check  all  of  the  switches  operation.  If  any  switch  has 

not activated fully, you will need to adjust the slide rail 
attached to the Microwave cavity.

0. This  is  done  by  following  the  steps  to  remove  the 

"DRAWER/SLIDE RAIL REMOVAL" on page 30. After 
you have removed the slide rails, loosen the "2" screws 
holding the slide rail to the Microwave cavity and tilt the 
front  end  up  and  the  rear  end  down,  then  tighten  the 

STOP SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT

screws (Fig. S-1).

.Check  and  assure  that  the  cap  nuts  on  the  Drawer 

Support Angles are centered when passing through the 
cavity face plate.

After adjustment, check the following. 
.  In and out play of door remains less than 0.5mm when 

in the latched position. First check upper position of latch 
hook, pushing and pulling upper portion of drawer toward 
the oven face. Then check lower portion of the latch hook, 
pushing and pulling lower portion of the door toward the 
oven face. Both results (play in the door) should be less 
than 0.5mm.

2.  The  secondary  interlock  switch  interrupts  the  circuit 

before the door can be opened.

3.  Monitor switch contacts close when door is opened.
4.  Door  sensing  switch  contacts  open  when  door  is 

opened.

5. 

Reassemble the unit

 and check for microwave leakage 

around door with an approved microwave survey meter. 
(Refer to Microwave Measurement Procedure.

Latch Hook Left

Latch Hook Right

Fig. S-1

Содержание MMD24S







































Отзывы: