i
nsTallaTion
s
peCifiCaTions
g
as
R
egulaToR
and
e
leCTRiCal
C
onduiT
l
oCaTion
WARNING
Factory installed
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
3/4" regulator
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
(1/2" supply ok)
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
&ACTORYINSTALLED
REGULATOR
SUPPLYOK
Power cord
Gas Regulator and Electrical Conduit Location
Rear View
Your DACOR
®
range was equipped with a shipping cover to
protect the internal components prior to installation.
This cover must be removed and replaced by a DACOR
®
backguard for your range to function properly.
Be sure that the unit is not connected to gas or
power before proceeding.
1.
Unpack the contents of the box and verify parts with the Packing List.
2.
Remove the single screw on the top of the shipping cover.
3.
Slide the shipping cover off the unit.
Remove Screw
Shipping Cover
Shipping Cover
Shipping Cover Removal
(36” range shown)
4.
Locate and install the flue exhaust extensions at the rear of the range
(9" and 24" backguards only). Use the provided hex screws and
tighten securely into the pre-drilled holes.
ERD with 9” Flue Extension
(9" flue extension shown)
ERD48 with 9” Flue Extension
(9" flue extension shown)
5.
Remove the backguard from its box.
6.
To avoid scratches, place small scraps of thin cardboard on the rear
of the side panels where the backguard will make contact. With the
assistance of at least one other person, carefully lift the backguard
over the exhaust flues and place down on to the range top.
Special attention should be given to the lower flange in front of the
backguard, which must fit between the stainless steel side panels.
7.
Fasten the provided screws through the rear flange.
Backguard
Flue with Extension
(9" and 24" only)
ERD Backguard Installation
Backguard
Flue with Extension
(9" and 24" only)
ERD48 Backguard Installation
NOTE:
For 24” Backguards, fasten the provided screws
through the holes in the back panel of the Backguard.
8.
Connect the gas line to the regulator. Reposition and attach the
access panel or the back cover if the entire back cover was removed.
9.
You are now ready to continue with the range installation.
i
nsTalling
The
36"
and
48" R
ange
b
aCkguaRd
