i
nsTallaTion
s
peCifiCaTions
V
eRifying
The
p
aCkage
C
onTenTs
Verify that all required components have
been provided. If any item is missing or
damaged, please contact your dealer
immediately. Do not install a damaged or
incomplete appliance.
• Use & Care Manual
• Ignitor Cleaning Kit
• Broiler Pan/Grill
• Anti-tip Bracket (selected models)
• Grate/Burner Cap Packs
• Griddle
• Burner Rings
• Wok Ring
• Simmerplate
• Spatula
• Stainless Steel Cleaner
• Pry Stick
Dacor
®
Model No.
Electrical
Circuit
Required
Total
Connected
Load
Gas
Type
Manifold
Pressure
Min. Gas Supply
Pressure
EGR30
120VAC, 60Hz,
15A
0.75kW
(6A)
Natural
5” Water Column
6” Water Column
EGR30LP
Liquid
Propane
10” Water Column
11” Water Column
ERD30
120/240VAC,
60Hz, 30A
4.2kW
(22A)
Natural
5” Water Column
6” Water Column
ERD30LP
Liquid
Propane
10” Water Column
11” Water Column
ERD36
4.7kW
(24A)
Natural
5” Water Column
6” Water Column
ERD36LP
Liquid
Propane
10” Water Column
11” Water Column
ERDE36
120/240VAC,
60Hz, 40A
7.7kW
(34A)
Natural
5” Water Column
6” Water Column
ERDE36LP
Liquid
Propane
10” Water Column
11” Water Column
ERD48
120/240VAC,
60Hz, 50A
10.0kW
(46A)
Natural
5” Water Column
6” Water Column
ERD48LP
Liquid
Propane
10” Water Column
11” Water Column
ERDE48
10.8kW\
(48A)
Natural
5” Water Column
6” Water Column
ERDE48LP
Liquid
Propane
10” Water Column
11” Water Column
ERD60
120VAC, 60Hz,
30A
4.1kW
(21A)
Natural
5” Water Column
6” Water Column
ERD60LP
Liquid
Propane
10” Water Column
11” Water Column
Gas and Electrical Supply Requirements
It is the owner’s responsibility to ensure that the electrical
connection of this appliance is performed by a qualified
electrician. The electrical installation, including minimum supply
wire size and grounding, must be in accordance with the National
Electric code ANSI/NFPA 70-1993* (or latest revision) and local
codes and ordinances.
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
The correct voltage, frequency, and amperage must be supplied
to the appliance from a separate, grounded, circuit that is
protected by a properly sized circuit breaker or time delay fuse.
Refer to the data plate, and/or the table to the right, for gas supply
requirements.
NOTES:
1.
The power supply must be properly polarized.
Reverse polarity will result in continuous sparking
of the electrodes, even after flame ignition.
2.
If there is any doubt as to whether the power
supply is properly polarized or grounded, have it
checked by a qualified electrician.
3.
Two electrical circuits and gas supplies are
required for the ERD60.
NOTE:
The shaded areas shown in the illustrations, denote
the location of the gas stub and the electrical
junction box/receptacle. These are suggested
locations. For replacement purposes, the location
of the existing utilities may be utilized provided that
they do not interfere with the sides or rear of the
range. If installing the gas valve behind the range,
verify that local building codes will permit this.
A manual shut valve must be installed in the gas piping, external
to the appliance, for the purpose of turning on or shutting off
gas to the appliance. Plan the location of the range and the gas
supply to allow access to the valve when the unit is installed.
Access to the remote circuit breaker panel/fuse box, with the
range in place, must also be allowed for in the installation. Any
openings in the wall behind the appliance and in the floor under
the appliance must be sealed.
g
as
s
upply
R
equiRemenTs
e
leCTRiCal
p
oweR
s
upply
R
equiRemenTs
g
as
& e
leCTRiCal
R
ough
-i
n
l
oCaTions
Check your local building codes for the
proper method of installation. In the absence of local codes, this
appliance should be installed in accordance with the National
Fuel Gas Code ANSI Z223.1. Be certain that the appliance being
installed is correct for the gas service being provided. Refer to the
data plate located behind the inlet air cooling grill, and/or the table
to the right, for gas supply requirements. Open the oven door and
remove the inlet air cooling grill for access to the data plate.
WARNING
This appliance must be installed by a licensed
plumber or gas fitter when installed within the
Commonwealth of Massachusetts.
WARNING
If the gas or electric service provided does not meet
the product specifications, do not proceed with the
installation. Call the selling dealer, the gas supplier,
or a licensed electrician.
