10
Custom overlay panels used with models IF42 and IF48 allow you
to blend the exterior of your refrigerator into the overall kitchen
décor, and to use custom handles for additional design flexibility.
Panel Specifications
The custom panels must have backer panels attached in order
•
to mount them to the refrigerator. It is most common to work
with three layers, as shown in the illustrations below. The three
layers consist of a decorative overlay panel, a ¹/
8
” (3.18 mm)
spacer panel or spacer strips and a ¼” (6.35 mm) backer panel.
In some cases, instead of constructing the panel using three
•
layers, the cabinet manufacturer may choose to work with a
single piece routed for the different dimensions. Follow the
panel dimension and placement instructions on the facing page
to be sure that the custom overlay panels will fit properly.
To minimize panel weight, you may use 2” (5.08 cm) spacer
•
strips around the perimeter in place of full-sheet solid spacer
panels. The spacer strips must be set in at least 1” (2.54 cm)
from the top, bottom and side edges of the backer panel. If you
use spacer strips, it is also recommended that you use two 2”
(5.08 cm) strips horizontally centered for added support.
For the grille and the door panels to be flush, the overlay door
•
panel should be ¼” (6.35 mm) thicker than the overlay grille
panel.
IMPORTANT
:
Install the custom panels only after moving the refrigerator into
•
place (see page 16).
The weight of the overlay panels cannot exceed:
•
50 lbs (23 kg) for the refrigerator door
-
30 lbs (13.5 kg) for the freezer door (total)
-
10 lbs (4.5 kg) for the top grille
-
Important Information About Freezer Door Overlay
Panels on Dispenser Models:
There are two basic methods for paneling the freezer door on
•
dispenser models:
Frameless method
-
Framed method
-
The framless method involves fabricating two separate panels
•
for above and below the dispenser that slide in from the handle
side of the door.
The framed method involves fabricating a single overlay panel
•
and attaching two separate sets of spacer and backer panels
above and below the dispenser cutout (see facing page). The
completed panel slides into place as a single unit.
IMPORTANT:
The dispenser is recessed behind the overlay
panel for the freezer door. The edges of the overlay panel around
the bottom of the dispenser may be exposed to water during
normal use. Seal the area around the dispenser to prevent water
seepage and damage. It is suggested that the edges of the
panel around the bottom the dispenser be covered by waterproof
material to prevent damage to the finish over time.
Installation Requirements
Custom Panels and Handles - IF42/IF48 Series Models
Overlay Panel
Overlay Panel
Spacer Panel
Backer Panel
Backer Panel
Door
5
/
8
" to
3
/
4
"
(1.6 to 1.9 cm)
1
/
8
"
(3.2 mm)
1
/
4
"
(6.4 mm)
1" minimum*
(2.5 cm)
Door/Grille Trim
Spacer Panel
Offset Dimension
1
/
8
"
(3.2 mm)
Overlay Panel
Overlay Panel
Spacer Panel
Backer Panel
Backer Panel
Door
5
/
8
" to
3
/
4
"
(1.6 to 1.9 cm)
1
/
8
"
(3.2 mm)
1
/
4
"
(6.4 mm)
1" minimum*
(2.5 cm)
Door/Grille Trim
Spacer Panel
Offset Dimension
1
/
8
"
(3.2 mm)
* The spacer panel offset must be a minimum
of 1” (2.5 cm) from all four edges of each
backer panel, including the edges next to the
dispenser (on dispenser models).
