Dacor DISCOVERY DYF48BNDI, Инструкция по использованию и уходу

Страница: 17 / 20

15
Product Data Sheets
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33° - 100°F (0.6° - 37.8°C)
Service Flow Rate 0.5 GPM (3.2 Lpm) @ 60 psi.
„
It is essential that operational, maintenance and filter
replacement requirements be carried out for the product to
perform as advertised.
„
Use replacement filter P2RFGG2, Dacor part # AFF6. Visit
www.everythingdacor.com or call 1-800-253-1302 (In Canada
call 1-800-807-6777).
„
When the water filter status display changes from GOOD to
ORDER FILTER, order a new filter. When the filter indicator
reads REPLACE FILTER, it is recommended that you replace
the filter.
„
These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
„
The product is for cold water use only.
„
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.
„
Refer to the Warranty and Service section for the
Manufacturer’s name, address and telephone number.
„
Refer to the Warranty and Service section for the
Manufacturer’s limited warranty.
Base Grille Water Filtration System
Model P2RFGG2/P2WG2L, P2WG2, P1WG2L, P1WG2
Capacity 200 Gallons (757 Liters)
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction
Aesthetic Effects
NSF Reduction
Requirements
Average
Influent
Influent Challenge
Concentration
Maximum
Effluent
Average
Effluent
Minimum %
Reduction
Average %
Reduction
Chlorine Taste/Odor
Particulate Class I
50% reduction
85% reduction
2.0182 mg/L
1333333 #/mL
2.0 mg/L ± 10%
At least 10,000 particles/mL
0.06 mg/L
6600 #/mL*
0.0536 mg/L
2325 #/mL
97.03
99.51
97.39
99.9
Contaminant
Reduction
NSF Reduction
Requirements
Average
Influent
Influent Challenge
Concentration
Maximum
Effluent
Average
Effluent
Minimum %
Reduction
Average %
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.5
0.010mg/L
0.010mg/L
0.1533 mg/L
0.1400 mg/L
0.15 mg/L ± 10%
0.15 mg/L ± 10%
0.0005 mg/L
0.0007 mg/L
0.0005 mg/L
0.0006 mg/L
99.67
99.50
99.29
99.14
Mercury: @ pH 6.5
Mercury: @ pH 8.5
0.002 mg/L
0.002 mg/L
0.0058 mg/L
0.0059 mg/L
0.006 mg/L ± 10%
0.006 mg/L ± 10%
0.0002 mg/L
0.0005 mg/L
0.0002 mg/L
0.0003 mg/L
96.54
91.57
96.25
82.72
Benzene 0.005 mg/L 0.0154 mg/L 0.015 ± 10% 0.0012 mg/L 0.0006 mg/L 92.22 96.88
O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58 99.97
Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% 0.001 mg/L 0.001 mg/L 93.33 92.77
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate
Class I; and against NSF/ANSI Standard 53 for the reduction of Mercury,
Benzene, Toxaphene, O-dichlorobenzene, and Lead.
* Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
® NSF is a registered trademark of NSF International.
Manufactured for Whirlpool Corporation (Benton Harbor, MI) by Kemflo International (Pingtung, TW)