background image

3

MORE SCREEN DROP

1. Place operating switch in 

“down”

position.

2. When the screen stops, turn the white 

“down” 

limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising

picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained.

CAUTION: Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. This
screen comes standard with 0" or 2" black at the top. See the specification data sheet for details.

LESS SCREEN DROP

1. Raise picture surface approximately two feet above desired level.

2. Place operating switch in 

“off”

position.

3. Turn the white 

“down”

limit switch (Fig. 2) one-quarter turn clockwise. Test by raising picture surface

approximately two feet, then lower again. Repeat until desired picture surface position is attained.

DIRECTOR ELECTROL

®

INSTRUCTIONS

220 / 240V WIRING DIAGRAM

WITH ONBOARD LVC

120V WIRING DIAGRAM

WITH ONBOARD LVC

BLACK

WHITE

WHITE
RED (UP)
GRAY
BLACK (DOWN)
GREEN

DOOR SWITCH

SCREEN MOTOR

BLACK

WHITE

BLACK AND YELLOW

LOW-VOLTAGE
WALL SWITCH

BLACK

WHITE

RED

OPTIONAL RF OR IR
REMOTE CONNECTOR

LVC BOARD

WHITE (COMMON)

BLACK (DOWN)

RED (UP)

INPUT

GROUND
BLACK (HOT)
WHITE (COMMON)

120VAC 60HZ
INPUT

DOOR MOTOR

BLACK (CLOSE)

WHITE
RED (OPEN)

GREEN

DOWN

STOP

UP

BROWN

BLACK

BLUE

BLUE
BLACK (UP)
GRAY
BROWN (DOWN)
GREEN

DOOR SWITCH

SCREEN MOTOR

BROWN

BROWN AND
YELLOW

LOW-VOLTAGE
WALL SWITCH

AUX EYE

LVC BOARD

INPUT

GROUND

BLACK

BROWN (HOT)

BLUE
BLACK
BROWN (DOWN)
BLACK (UP)

220/240VAC 50/60HZ
INPUT

DOOR MOTOR

BROWN (CLOSE)
BLUE
BLACK(OPEN)

GREEN

DOWN

STOP

UP

RED

NOTE: Electrical connections on left end of
case.

NOTE: Electrical connections on left end of
case.

BLACK

WHITE

RED

EYE AUX

OPTIONAL RF OR IR
REMOTE CONNECTOR

!

Содержание DIRECTOR ELECTROL









Отзывы: