background image

3

6.  Remove switch assembly (boxed, located at pin end of fabric).

 

CAUTION! Do not cut wrapping paper or tape with knife or 
any sharp tool. Remove by hand.

7.  Pull orange string to remove wrapping paper.

8.  Install electrical hook up that applies to your unit. Standard 

installation is for a single 120VAC or 240VAC wall switch to 
control the screen. Optional Control units may have been 
ordered. Refer to additional instructions for the external VPI, 
external low voltage control and SCB-100. Refer to the 
appropriate wiring diagram for your screen.

 

NOTE:

 Screen has been internally wired at DA-LITE. Wiring 

designated “external” is completed by installer conforming to 
local and national codes.

9.  Lower picture surface approximately 4"-6" so that the slat will 

rest on top of the slat hooks.  Guide slat past hooks by gently 
pulling fabric forward (Fig. 3).  Do not bend hooks.

10.  Test installation by carefully running picture surface up and 

down 2-3 times. Be prepared to stop screen.  Standard Duty 
Cycle: 1 MIN. ON / 3 MIN. OFF.

11.  Run the picture surface upward. The surface door will 

automatically close when the picture surface rolls into the 
case. The ends of the slat will catch the two hooks on the 
surface door and pull the door closed. When the door closes, 
a limit switch is tripped and the motor shuts off.

 

CAUTION! Excessive continuous operation may cause 
overheating.

12.  Run picture surface downward until picture surface  

door fully opens.

13.  Install junction box cover plate.

14.  Close access door and reinstall screws at each end  

of access door.

 

CAUTION! Do not attempt to restore a lost wrap by 
adjusting limit switches. Allow one-eighth of an inch (1/8") 
clearance around surface door. Make sure door does not 
bind. Check hinges. Paint or tile cement will interfere with 
free operation. Gravity drops door.

15.  Complete installation by painting and finishing to suit  

your needs. Finish to allow access door to be removed  
if necessary.

Boardroom Electrol

®

 Installation

Figure 2

Содержание Boardroom ElEctrol











Отзывы: