background image

2

Important Safety Instructions

When using your video equipment, basic safety precautions 
should always be followed, including the following:

1.  Read and understand all instructions before using.

2.  Position the cord so that it will not be tripped over, pulled, or 

contact hot surfaces.

3.  If an extension cord is necessary, a cord with a current rating 

at least equal to that of the appliance should be used. Cords 
rated for less amperage than the appliance may overheat.

4.  To reduce the risk of electric shock, do not disassemble this 

appliance. Contact an authorized service dealer when repair 
work is required. Incorrect reassembly can cause electric 
shock when the appliance is used subsequently.

5.  The use of an accessory attachment not recommended by 

the manufacturer may cause a risk of fire, electric shock, or 
injury to persons.

Save These Instructions

Pre-Installation

Installation

1.  Carefully unpack screen and remove outer  

wrapping from case.

2.  Make sure to recheck measurement of screen  

location before installation.

3.  Remove center support brackets (on 8' and wider  

screens only), reverse brackets and reinstall flush with  
the top of the box.

NOTE:

 Unit is not to be installed in air handling space.

1.  Install screen by raising unit into position between joists at 

one end only. Install one lag screw or appropriate fastener in 
each mounting bracket. Secure opposite end. Secure center 
support brackets. Install sufficient fasteners in each bracket 
for secure installation.

2.  Make sure unit is level and plumb.

 

CAUTION! Do not secure access door or seal in unit  
until screen has been secured in position and properly 
tested for satisfactory operation. Do not fit unit so tightly 
that the screen surface drop door binds. Door drops by 
gravity only.

3.  If you are going to cover screen door with paneling or other 

materials, allow access (suitable holes or plug) to slat hook 
screws (4) when servicing (Fig. 1).

4.  Open access door by removing access door screws.

5.  Remove junction box cover plate.

Figure 1

Slat Hook 

Screws

Tape Strips

Figure 2

Fabric Door

Access  

Door 

Screw

Access Door

Mounting Brackets

Содержание Boardroom ElEctrol











Отзывы: