background image

7

MOUNTING OPTIONS

8. Holding the Satellite Speaker with both hands, reinsert the ball portion of the Ball and Shaft into the Attachment

Plate.

9. Hand-tighten the Molded Nut while positioning the speaker for the desired orientation. If the Molded Nut is difficult

to tighten by hand, insert the Metal Bar into one of the holes in the outer edge of the Molded Nut and use the bar
as a lever. Be careful not to cross-thread. The swiveling ball enables you to aim the speaker to one side or the
other, or to tilt it up or down.

10. Once the speaker’s orientation has been finalized, insert the Metal Bar into one of the holes in the outer edge of

the Molded Nut and tighten the Molded Nut securely. Keep the Metal Bar in a safe place in the event that you
decide to adjust the speaker’s orientation in the future.

DOLBY* DIGITAL OR DTS

®

(OR OTHER DIGITAL SURROUND MODE) CONNECTION

Use this installation method for Dolby Digital, DTS or
other digital surround processors:

1. Use the line-level input jack marked “LFE” for the

Low-Frequency Effects channel. Connect this jack
to the LFE output or subwoofer output on your
receiver or amplifier. Connect each speaker to the
corresponding speaker terminals on your receiver
or amplifier.

2. Make sure that you have configured your surround

sound processor for “Subwoofer On”. Also
configure your receiver for 5.1-, 6.1- or 7.1-channel
operation as appropriate. The front left, front right,
center and rear speakers should all be set to
“Small”. If your receiver allows you to set the
crossover frequency between the subwoofer and
the main speakers, select 100Hz or the setting
that is the closest frequency below it.

LINE

LEVEL

IN

LFE

L

R

LFE OUT

SUBWOOFER

RECEIVER

Содержание ACOUSTICAL IMAGER













Отзывы: