![background image](http://html.mh-extra.com/html/da-lite/acoustical-imager/acoustical-imager_instruction-book_495204007.webp)
6
MOUNTING OPTIONS
3. Gently pull the slack out of the wire and screw the
adaptor onto the back of the speaker in two
places, as shown.
4. The floor stand adaptor screws may be found in
Hardware Bag B. Use the larger screw in the
upper screw hole, and the smaller screw in the
lower screw hole.
5. Screw the floor stand adaptor into the floor
stand’s threaded insert until the speaker is firmly
attached to the stand. Back off slightly from the
fully-tightened position until the speaker is
oriented as desired, then rotate the thumbwheel
at the bottom of the floor stand adaptor to secure
the speaker to the stand.
WALL MOUNTING
NOTE: The customer is solely responsible for proper selection
of mounting hardware not included with the speakers, and for
proper assembly and installation of the wall-brackets,
including but not limited to the selection of the appropriate
weight-bearing supports and proper use of the bracket. Be
sure to follow these bracket assembly and installation
instructions carefully. If you have any questions or doubts
about your ability to correctly wall-mount the speakers,
consult with Da-Lite customer service.
1. Unscrew and remove the large molded nut. If
necessary, use the supplied Metal Bar as a lever
by inserting it into one of the holes in the outer
edge of the Molded Nut.
2. Firmly grasp the Ball and Shaft and pull it straight
out of the Attachment Plate. Avoid leaning it to
the side for leverage, as this may break off a tab.
3. Slide the Molded Nut onto the Ball and Shaft with
the threaded opening facing the ball. Thread the
metal nut all the way onto the Ball and Shaft, with
the star washer side away from the ball. Refer to
the exploded drawing for the proper orientation of
these parts.
4. Screw the Ball and Shaft into the Threaded Insert
on the back of the Satellite Speaker until it is fully
seated in the Threaded Insert, but
do not
tighten as
you might dislodge the Threaded Insert. Such
damage would not be covered under the warranty.
5. Tighten the Metal Nut with the star washer side
between the Metal Nut and the back of the
Satellite Speaker, using large needle-nose pliers,
until it is firmly seated against the back of the
Speaker and has locked the Ball and Shaft and the
Satellite Speaker together. Note that once the
Metal Nut is fully tightened, it may embed some
marks on the back of the Satellite Speaker.
However, these marks will be covered by the
Metal Nut.
6. Mount the Attachment Plate into a wood stud on
the wall, using four #10 pan-head wood screws at
least one inch long (not supplied). Make sure that
all four screws are driven into the stud and not
into drywall.
NOTE: If the bracket needs to be mounted in drywall,
the customer is responsible for selecting and using
appropriate wall-anchors and screws.
NOTE: The Metal Nut must be fully tightened against the
Satellite Speaker as described in Step 5 before beginning
Step 8 in order to avoid damage to the Threaded Insert. Such
damage would not be covered under the warranty.
7. Connect the supplied speaker wires to the
surround speaker terminals, press the red or black
plastic cap for the desired terminal, insert the bare
end of the wire into the hole below the cap and
release the cap. Gently tug on the wire to make
sure that it is fully inserted.
ATTACHMENT
PLATE
BALL AND SHAFT
METAL NUT
MOLDED NUT
METAL BAR
#10 PAN-HEAD
WOOD SCREW
(NOT SUPPLIED)
4-PIECES
SATELLITE SPEAKER
THREADED INSERT
MOLDED NUT
BALL AND SHAFT
ATTACHMENT
PLATE
#10 PAN-HEAD
WOOD SCREW
(NOT SUPPLIED)
4-PIECES
METAL BAR
METAL NUT