D-M-E VCTB-4000 Скачать руководство пользователя страница 3

D-M-E Company 

VCTB-4000 

Page 3 

 

ED-0109-OT-024-( Preliminarry Rev E) 

 

WARRANTY 

 

D-M-E  Company  warrants  that  this  product  will  be  free  from  defects  in  materials  and  workmanship  for  a 
period  of  three  (3)  years  from  the  date  of  shipment.    If  any  such  product  proves  defective  during  this 
warranty  period,  D-M-E  Company,  at  its option, either will repair the defective product without charge for 
parts and labor, or will provide a replacement in exchange for the defective product. 
 
This  warranty  shall  not  apply  to  any  defect,  failure  or  damage  caused  by  improper  use  or  improper  or 
inadequate  maintenance  and  care.    D-M-E  Company  shall  not  be  obligated  to  furnish  service  under  this 
warranty  a)  to  repair  damage  resulting  from  attempts  by  personnel  other  than  D-M-E  Company 
representatives  to  repair  or  service  the  product;  b)  to  repair  damage  resulting  from  improper  use  or 
connection to incompatible equipment; or c) to service a product that has been modified or integrated with 
other  products  when  the  effect  of  such  modification  or  integration  increases  the  time  or  difficulty  of 
servicing the product. 

Содержание VCTB-4000
















Отзывы: