D-Link DSL-2320B Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 63

background image

10

D-Link DSL-30B ADSL+ Ethernet/USB Modem User Manual

Section 5 - USB Installation

USB Driver Installation

To connect your computer to the modem by the USB cable instead of the Ethernet cable, you will need to install the
modem’s USB driver. If you are completing the setup using the ethernet port on the modem, skip this section and
proceed to “Configuring your Computer”. The following are general steps (may vary for each computer) to complete
the USB driver installation on a Windows

®

000/XP operating system.

The following pop-up window appears when you
connect the USB cable to your computer (with the
other end already attached to the modem).

The

Found New Hardware Wizard

will appear on

your screen. To continue, click

Next

.

«
...
8
9
10
11
12
...
»

Содержание DSL-2320B
































































Отзывы:

Нет отзывов

Похожие инструкции для DSL-2320B

Бренд: ADTRAN Страницы: 57

Бренд: 3Com Страницы: 160

Бренд: ActionTec Страницы: 2

Mtx MTX-STARENERGY-M

Бренд: Flexitron Страницы: 41

Бренд: Satel Страницы: 30

Бренд: Telenetics Страницы: 273

Бренд: Digi Страницы: 252

Бренд: Patton electronics Страницы: 10

Бренд: ADTRAN Страницы: 4

Бренд: ADTRAN Страницы: 80

Бренд: Zoom Страницы: 36

Бренд: Palm Страницы: 20

819-1XRT SERIES

Бренд: Cal Amp Страницы: 48

COMSPHERE 3810Plus

Бренд: Paradyne Страницы: 28

Бренд: IBM Страницы: 40

ORBCOMM IDP-280

Бренд: SkyWave Страницы: 63

Бренд: B+B SmartWorx Страницы: 2

Бренд: Unitronics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды