D-Link DES-3226SM - 1000Mbps Ethernet Switch страница 4 Скачать руководство пользователя

Страница: 4 / 233

Warranty service may be obtained by contacting a D-Link office within the applicable warranty

period, and requesting a Return Material Authorization (RMA) number. If a Registration Card

for the product in question has not been returned to D-Link, then a proof of purchase (such as a

copy of the dated purchase invoice) must be provided. If Purchaser's circumstances require

special handling of warranty correction, then at the time of requesting RMA number,

Purchaser may also propose special procedure as may be suitable to the case.

After an RMA number is issued, the defective product must be packaged securely in the

original or other suitable shipping package to ensure that it will not be damaged in transit, and

the RMA number must be prominently marked on the outside of the package. The package

must be mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance

prepaid. D-Link shall never be responsible for any software, firmware, information, or memory

data of Purchaser contained in, stored on, or integrated with any product returned to D-Link

pursuant to this warranty.

Any package returned to D-Link without an RMA number will be rejected and shipped back to

Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a

reasonable handling charge in addition mailing or shipping costs.

Software:

Warranty service for software products may be obtained by contacting a D-Link office within

the applicable warranty period. A list of D-Link offices is provided at the back of this manual,

together with a copy of the Registration Card. If a Registration Card for the product in

question has not been returned to a D-Link office, then a proof of purchase (such as a copy of

the dated purchase invoice) must be provided when requesting warranty service. The term

"purchase" in this software warranty refers to the purchase transaction and resulting license to

use such software.

D-Link warrants that its software products will perform in substantial conformance with the

applicable product documentation provided by D-Link with such software product, for a period

of ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link

warrants the magnetic media, on which D-Link provides its software product, against failure

during the same warranty period. This warranty applies to purchased software, and to

replacement software provided by D-Link pursuant to this warranty, but shall not apply to any

update or replacement which may be provided for download via the Internet, or to any update

which may otherwise be provided free of charge.

D-Link's sole obligation under this software warranty shall be to replace any defective software

product with product which substantially conforms to D-Link's applicable product

documentation. Purchaser assumes responsibility for the selection of appropriate application

and system/platform software and associated reference materials. D-Link makes no warranty

that its software products will work in combination with any hardware, or any application or

system/platform software product provided by any third party, excepting only such products as

are expressly represented, in D-Link's applicable product documentation as being compatible.

D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility,

but D-Link shall have no obligation to provide compatibility when there is fault in the third-

party hardware or software. D-Link makes no warranty that operation of its software products

will be uninterrupted or absolutely error-free, and no warranty that all defects in the software

product, within or without the scope of D-Link's applicable product documentation, will be

corrected.

Содержание DES-3226SM - 1000Mbps Ethernet Switch










































































































































































































































Результаты поиска

Содержание DES-3226SM - 1000Mbps Ethernet Switch

Отзывы:

Похожие инструкции для DES-3226SM - 1000Mbps Ethernet Switch

Бренды по названию

Популярные бренды

D-Link DES-3226SM - 1000Mbps Ethernet Switch, Справочное руководство

Результаты поиска

Содержание DES-3226SM - 1000Mbps Ethernet Switch

Отзывы:

Похожие инструкции для DES-3226SM - 1000Mbps Ethernet Switch

Бренды по названию

Популярные бренды