background image

12

D-Link DCS-6004L/DCS-6005L User Manual

Section 2: Installation

Please refer to the steps below to assist you with mounting the camera.

Mounting the Camera

2. Place the mounting base alignment sticker where you want to position the camera. 

Depending on the material of the wall or ceiling, use proper tools to drill two holes where 

you placed the alignment sticker. If the wall is made out of concrete, drill the holes first, then 

insert the plastic anchors to support the screws.

4. With the D-Link logo facing you, reattach the camera to the mounting plate by sliding the 

camera towards you until it locks into position.

5. Adjust the angle of the camera as desired, then tighten the collar on the camera stem to lock 

it in place.

3. Place the mounting base over the holes that are in the wall. Make sure to align the mounting 

base holes with the holes in the wall. Use the supplied screws to attach the mounting base to 

the surface of the wall.

1. The camera needs to be separated from the mounting base to expose the holes in the 

mounting base. Remove the camera head from the mounting base by firmly holding the 

camera with the D-Link logo facing you and then sliding the mounting base towards you.

We suggest that you configure the camera before mounting.

Do not overtighten screws as this may crack the mount.

2

1

4

5

3

4

Содержание DCS-6004L? DCS-6005L




























































Отзывы: