Cyrus DAC X Signature, Инструкция пользователя, Страница: 9 / 23

Cyrus DAC X Signature User Instructions
7
seTTINg uP (dAc X sIgNATuRe)
There are many configuration options available in the setup menu to customise
the DAC X Signature to best match each individual system.
To enter the menu system, press the front panel SETUP key f . Turn the
Rotary control e to scroll through the options available on the display.
Press the Rotary control
e
to select the option displayed. During the
setup sequence, you can move to the next or previous step by pressing
the Input up or down buttons.
Press the SETUP
f key to exit setup and save any changed settings.
Note that the setup sequence will exit, saving any changed settings after
10 seconds of inactivity or after the last option ‘Name input 6’ has been
completed.
The setup menu options are shown here –
Input display
Small Input Names
Display Mode
There are two modes of display operation. The small setting will show
a two-line display with the selected input in the display centre and the
current sample rate/lock status at the bottom. The large setting will show
a single line display with a larger input legend.
Input names
Input name
Input 1
DVD
< >
When the DAC X Signature leaves the factory, the input names are set to
correspond to the rear panel connections, for example Input 1 will display
as Input 1.
The name of any input may be changed to a choice from the following
list-
No source (off) •
LaserDisc, DVD, DVD 2, DVD-A, CD, CD 2 •
Linkserver, Linkport •
Jukebox, Phono •
Tuner, DAB, TV, AV, Cyrus AV, Satellite, Satellite 2, Cable •
Video, VCR, VCR 2, Tape, MiniDisc, DAT •
PC, Games, Keyboard, Aux, AV Direct, Stream X •
To change the names of the inputs, we recommend making a list of each
input number with your preferred name from the choices above before
setting the names.
No source is a special function name, used to name inputs that have no
source connected to them. These input numbers will not then appear in
the input selector sequence.
Restoring factory settings
You can also restore all configuration options to the initial default settings
that were applied at the factory.
NOTE: This operation is not reversible.
To restore factory settings, disconnect mains power from the unit. Now
re-connect mains power while holding down the Standby key.
Digital filter
Display options
Connected to:
Name Input 1
Choose a name for input 1 from the name list
Choose a name for input 2 from the name list
Choose a name for input 3 from the name list
Choose a name for input 4 from the name list
Choose a name for input 5 from the name list
Choose a name for input 6 from the name list
Name Input 2
Name Input 3
Name Input 4
Name Input 5
Name Input 6
Storing settings
Save settings and exit setup
Phase adjust
Select normal or inverted
Select fast or slow roll off
Select large or small
Select CD, TU, AU or AV
Setup
Phase adjust
Normal
Phase
This menu option sets the audio phase for the DAC. The factory setting is
normal. Some listeners may prefer the inverted setting with their systems
or for when playing particular recordings.
digital filter Response
Fast Roll-off
Digital Filter Response
This menu option gives two settings for the digital filtering of the DAC
stage. Choose your preference of Fast or Slow roll-off by auditioning
some of your favourite tracks with each setting.
dAcX connected to:
This option may be used to change the remote control and MC-BUS
response of the DAC X Signature. From the factory, the DAC X Signature
will power on in response to a CD select command from a Cyrus remote
control or from a CD select signal sent via MC-BUS, so if the DAC X
Signature is connected to the CD input of the amplifier, no change will
be required to this setting. If, however, the DAC X Signature is connected
to the TU, AU or AV inputs of the amplifier, the appropriate remote and
MC-BUS responses may be selected through this menu option to ensure
power-on compatibility with the amplifier.