Cypress EZ-BLE PRoC страница 1 Скачать руководство пользователя

Страница: 1 / 38

PRELIMINARY

CYBLE-212020-01

EZ-BLE



PRoC



Bluetooth 4.2 Module

Cypress Semiconductor Corporation

•

198 Champion Court

•

San Jose

CA 95134-1709

•

408-943-2600

Document Number: 002-12597 Rev. **

Revised April 21, 2016

General Description

The CYBLE-212020-01 is a fully certified and qualified module
supporting Bluetooth



Low Energy (BLE) 4.2 wireless communi-

cation. The CYBLE-212020-01 is a turnkey solution and includes
onboard crystal oscillators, trace antenna, passive components,
and the Cypress PRoC™ BLE. Refer to the CYBL10XX7X

datasheet

for additional details on the capabilities of the PRoC

BLE device used on this module.

The CYBLE-212020-01 supports a number of peripheral
functions (ADC, timers, counters, PWM) and serial
communication protocols (I

C, UART, SPI) through its

programmable architecture. The CYBLE-212020-01 includes a
royalty-free BLE stack compatible with Bluetooth 4.1 and
provides up to 23 GPIOs in a 14.52 × 19.20 × 2.00 mm package.

The CYBLE-212020-01 is drop-in compatible with the
CYBLE-01211-00 (128KB BT 4.1) and CYBLE-212019-00
(256KB BT 4.1) EZ-BLE PRoC Modules.

The CYBLE-212020-01 is a complete solution targeted at appli-
cations requiring cost optimized BLE wireless connectivity.

Module Description

■

Module size: 14.52 mm ×19.20 mm × 2.00 mm (with shield)

■

Castelated solder pad connections for ease-of-use

■

256-KB flash memory, 32-KB SRAM memory

■

Up to 23 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digial, or strong output

■

Bluetooth 4.2 single-mode module

■

Certified to FCC, IC, MIC, KC, and CE regulations

■

Industrial temperature range: –40 °C to +85 °C

■

32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz

■

Watchdog timer with dedicated internal low-speed oscillator
(ILO)

■

Two-pin SWD for programming

Power Consumption

■

TX output power: –18 dbm to +3 dbm

■

Received signal strength indicator (RSSI) with 1-dB resolution

■

TX current consumption of 15.6 mA (radio only, 0 dbm)

■

RX current consumption of 16.4 mA (radio only)

■

Low power mode support

❐

Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on

❐

Hibernate: 150 nA with SRAM retention

❐

Stop: 60 nA with XRES wakeup

Functional Capabilities

■

Up to 22 capacitive sensors for buttons or sliders with
best-in-class signal-to-noise ration (SNR) and liquid tolerance

■

12-bit, 1-Msps SAR ADC with internal reference,
sample-and-hold (S/H), and channel sequencer

■

Two serial communication blocks (SCBs) supporting I

(master/slave), SPI (master/slave), or UART

■

Four dedicated 16-bit timer, counter, or PWM blocks
(TCPWMs)

■

LCD drive supported on all GPIOs (common or segment)

■

Programmable low voltage detect (LVD) from 1.8 V to 4.5 V

■

S master interface

■

Bluetooth Low Energy protocol stack supporting generic
access profile (GAP) Central, Peripheral, Observer, or
Broadcaster roles

■

Switches between Central and Peripheral roles on-the-go

■

Standard Bluetooth Low Energy profiles and services for
interoperability

■

Custom profile and service for specific use cases

Benefits

The CYBLE-212020-01 module is provided as a turnkey
solution, including all necessary hardware required to use BLE
communication standards.

■

Proven hardware design ready to use

■

Cost optimized for applications without space constraint

■

Reprogrammable architecture

■

Fully certified module eliminates the time needed for design,
development and certification processes

■

Bluetooth SIG qualified with QDID and Declaration ID

■

Flexible communication protocol support

■

PSoC Creator

™

provides an easy-to-use integrated design

environment (IDE) to configure, develop, program, and test a
BLE application

Содержание EZ-BLE PRoC







































Результаты поиска

Содержание EZ-BLE PRoC

Отзывы:

Похожие инструкции для EZ-BLE PRoC

Бренды по названию

Популярные бренды

Cypress EZ-BLE PRoC, Руководство пользователя

Результаты поиска

Содержание EZ-BLE PRoC

Отзывы:

Похожие инструкции для EZ-BLE PRoC

Бренды по названию

Популярные бренды