Cypress CP-255D, Руководство по эксплуатации

Страница: 7 / 12

Specifications:
HDMI 1.2 Compliant
Input format (Up to 165MHz) Output format (Up to 165MHz)
for CP-255D for CP-255D
* 480i 30x2 / 576i 25x2 * 480i 30x2 / 576i 25x2
Input connectors:
- YCbCr/YPbPr x 1 via 3 RCA jack
- PC RGB x 1 via 15 pin D-sub
- DVI (CP-255D)x 1
Output connector:
- DVI (CP-255D)x 1
- PC 15 pin D-sub x 1 (CP-255D)
Dimension: 180(W)x124(D)x25(H)mm
Weigh: 600gs
DC 5V 2.6 Amp
8
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@(60/72/75/85)
SVGA@(56/60/72/75/85)
XGA@(60/70/75/85)
SXGA@(60/75/85)
UXGA@60
WXGA@60(1280X800)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
Resolution
INPUT
Component D-SUB DVI/HDMI
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
*
V
V
V
V
V
V
V
V
V
V
V
V
OUTPUT
D-SUB DVI/HDMI
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@(60/72/75/85)
SVGA@(56/60/72/75/85)
XGA@(60/70/75/85)
SXGA@(60/75/85)
UXGA@60
WXGA@60(1280X800)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
Resolution
V(@60)
V(@60)
V(@60)
V(@60)
V
V
V
V
V
V
*
V
V
V
V
V(@60)
V(@60)
V(@60)
V(@60)
V(@60)
V
V
V
2. DVI input: Connects this DVI input connector to the DVI output connector of
your DVI source equipment. The DVI input should be digital DVI only and
should not include analog RGB signal.
The use of DVI-I connector is to ensure both DVI-I and DVI-D male connector
of the DVI cable can fit into this input connector. The digital DVI input
resloution can range from 480i~1080p, or VGA~WUXGA.
3. PC-D sub out: The connector for scaled analog RGB output.
Connect this output port to the analog PC RGB input of your monitor, or
connect it to the RGBHV input of your HD display using D-sub to 5 BNC
adaptor cable. (not included in the package)
Note: When input is a HDCP encrypted DVI signal this analog output will be
turned off.
4. DVI output: Scaled digital DVI output. Connect this output to the DVI input or
HDMI input of your Digital display.
Note: When input is a HDCP encrypted DVI signal the DVI output is also HDCP
encrypted. The monitor/display that connected to this output also need to
be HDCP compliant in order to get a nice and clean picture. A non-HDCP
compliant display can only display non-HDCP signal and picture will
become noise when input is a HDCP-encrypted signal.
5. Power jack: Connect to the 5V 2A DC power adaptor.
Remote Control and functions:
1. Power: Press the button once to power on the CP-255D. Press again to enter
standby mode.
2. Input: Press the button repeatedly to toggle through various input sources as
follows.
3. HD input: Press the button to select component input.
4. PC input: Press the button to select PC input.
5. HDMI/DVI input: Press the button to select DVI (or HDMI) input.
6. Output resolution:
Select buttons: Press any one of the button to directly
select output resolution.
For other output resolutions that are not
covered by these buttons please enter
Menu/Output page to select them.
7. MENU: Press the button to bring up OSD main menu page.
8. Exit: Press the button to exit from a sub menu or main
menu.
9. Up/Down/Left/Right: Press the Up/Down button to move
the highlight bar to your desired
parameter during the OSD operation.
Press the Left/Right button to increase/
decrease the setting value of a
selected parameter.
4
10. OK (Enter): Press the button to confirm your selection.
11. Reset: Press the button to reset the unit's firmware setting to the factory
default value.
12. Auto Adjust: Press the button to optimize the position of the picture
(picture centering) on the screen.
(5).Installation
Input Connection
PC OUT DVI OUT PC IN DVI IN DC 5V
HDMI
HDMI
HDMI
HDMI
Cable
DVI
HDMI out
DVD
DVI out
PC
STB
PC
or
DVI
Cable
PC-in
HDMI to DVI
connector
adaptor
Component out
DVD or Set Top Box
Component in
Y/HD
Cb/Pb
Cr/Pr
HD PC DVI
MENU POWER INPUT
ENTER
-
+
INPUT
AUTO
ADJUST