manualshive.com logo in svg

Cypress AN214934, Руководство пользователя

Поделиться
Скачать
Cypress AN214934 Скачать руководство пользователя страница 3

Bluetooth Low Energy Current Consumption Measurements

www.cypress.com

Document No. 002-14934 Rev. *C

2

1.2

Acronyms and Abbreviations

In most cases, acronyms and abbreviations are defined on first use.

For a comprehensive list of acronyms and other terms used in Cypress documents, go to:

http://www.cypress.com/glossary

1.3

References

The references in this section may be used in conjunction with this document.

Note: 

Cypress provides customer access to technical documentation and software through its Cypress Developer 

Community and Downloads & Support site (see 

Overview

).

For Cypress documents, replace the “xx” in the document number with the largest number available in the reposi-
tory to ensure that you have the most current version of the document.

2

IoT Resources

Cypress provides a wealth of data at 

http://www.cypress.com/internet-things-iot

 

to help you to select the right IoT

device for your design, and quickly and effectively integrate the device into your design. Cypress provides cus-
tomer access to a wide range of information, including technical documentation, schematic diagrams, product bill
of materials, PCB layout information, and software updates. Customers can acquire technical documentation and
software from the Cypress Support Community website (

http://community.cypress.com/

).

3

Overview

The Bluetooth Low Energy (BLE) technology is a global standard for very low-power wireless technology. The BLE
devices can operate from coin cell batteries for applications that use low data rates. BLE devices can communi-
cate wirelessly to dual mode Bluetooth-enabled devices. The connections are designed to be robust, short range,
and low cost. The BLE-enabled devices are used in the area of fitness, advertising, medical, security, and home
entertainment.

4

Comparing Bluetooth Low Energy to Bluetooth 2.x/3.x

The similarities between the Bluetooth and the BLE technology allow a Bluetooth transceiver to have dual-mode
operation. Bluetooth and BLE technology can coexist in one device. For example, a BLE radio can use the follow-
ing items from an existing Bluetooth radio:

■

Radio architecture

■

Host controller interface (HCI) logical and physical transports

■

Logical link control and adaptation protocol (L2CAP)

The BLE technology differs from Bluetooth in the following areas:

■

Discovery and connection procedures are handled differently when it comes to lowering total power consump-
tion.

■

BLE is limited to only one packet type.

■

Connections are entered and always exited in sniff-like mode. 

■

Transmit and receive operations are governed by interframe spacing as opposed to being slot oriented. 

■

Profiles are thinner than standard Bluetooth and are structured around client/server architecture. 

■

BLE devices have lower duty cycles and only three advertising channels to lower connection time. The shorter 
enable and connection times result in lowering total power consumption. 

Document (or Item) Name

Broadcom 

Document Number

Cypress 

Document Number

Source

Cypress Items

Cypress Bluetooth/WLAN Motherboard For 

Cypress Bluetooth and Wireless LAN 

Applications Testing, BCM9UMB Hardware 

User Manual

9UMB-HWUM100-R 

–

Cypress Developer Community

 

 

Содержание AN214934

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды