Cypress Semiconductor CY7C64013C Скачать руководство пользователя страница 29

Страница: 29 / 51

CY7C64013C

CY7C64113C

Document #: 38-08001 Rev. *B

Page 29 of 51

16.0

Interrupts

Interrupts are generated by the GPIO/DAC pins, the internal timers, I

C-compatible interface or HAPI operation, or on various

USB traffic conditions. All interrupts are maskable by the Global Interrupt Enable Register and the USB End Point Interrupt Enable

Global Interrupt Enable Register

ADDRESS 0X20

Bit 0

USB Bus RST Interrupt Enable

1= Enable Interrupt on a USB Bus Reset; 0 = Disable interrupt on a USB Bus Reset (Refer to section 16.3)

Bit 1 :128-µs Interrupt Enable

1 = Enable Timer interrupt every 128 µs; 0 = Disable Timer Interrupt for every 128 µs.

Bit 2 : 1.024-ms Interrupt Enable

1= Enable Timer interrupt every 1.024 ms; 0 = Disable Timer Interrupt every 1.024 ms.

Bit 3 : Reserved
Bit 4 : DAC Interrupt Enable

1 = Enable DAC Interrupt; 0 = Disable DAC interrupt

Bit 5 : GPIO Interrupt Enable

1 = Enable Interrupt on falling/rising edge on any GPIO; 0 = Disable Interrupt on falling/rising edge on any GPIO (Refer to

section 14.7, 9.1 and 9.2.)

Bit 6 : I

C Interrupt Enable

1= Enable Interrupt on I2C related activity; 0 = Disable I2C related activity interrupt. (Refer to section 16.8).

Bit 7 : Reserved

USB Endpoint Interrupt Enable

ADDRESS 0X21

Bit 0

EPA0 Interrupt Enable

1= Enable Interrupt on data activity through endpoint A0; 0= Disable Interrupt on data activity through endpoint A0

Bit 1

EPA1 Interrupt Enable

1= Enable Interrupt on data activity through endpoint A1; 0= Disable Interrupt on data activity through endpoint A1

Bit 2

EPA2 Interrupt Enable

1= Enable Interrupt on data activity through endpoint A2; 0= Disable Interrupt on data activity through endpoint A2.

Bit 3

EPB0 Interrupt Enable

1= Enable Interrupt on data activity through endpoint B0; 0= Disable Interrupt on data activity through endpoint B0

Bit 4

EPB1 Interrupt Enable

1= Enable Interrupt on data activity through endpoint B1; 0= Disable Interrupt on data activity through endpoint B1

Bit [7..5] : Reserved

During a reset, the contents the Global Interrupt Enable Register and USB End Point Interrupt Enable Register are cleared,

effectively, disabling all interrupts

Bit #

Bit Name

Reserved

C Interrupt

Enable

GPIO Interrupt

Enable

DAC Interrupt

enable

Reserved

1.024-ms

Interrupt Enable

128-

s Interrupt

Enable

USB Bus RST

Interrupt Enable

Read/Write

R/W

Reset

Figure 16-1. Global Interrupt Enable Register

Bit #

Bit Name

Reserved

Reserved Reserved

EPB1

Interrupt

Enable

EPB0 Interrupt

Enable

EPA2 Interrupt

Enable

EPA1 Interrupt

Enable

EPA0 Interrupt

Enable

Read/Write

R/W

Reset

Figure 16-2. USB Endpoint Interrupt Enable Register

[+] Feedback

Содержание CY7C64013C




















































Результаты поиска

Содержание CY7C64013C

Отзывы:

Похожие инструкции для CY7C64013C

Бренды по названию

Популярные бренды

Cypress Semiconductor CY7C64013C, Техническое описание

Результаты поиска

Содержание CY7C64013C

Отзывы:

Похожие инструкции для CY7C64013C

Бренды по названию

Популярные бренды