background image

Perhaps the greatest environmental damage to wood furniture comes from wide swings in

relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity

rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and

contracts unequally along different grain directions. As humidity changes, the components

of wooden objects are continually pushing and pulling against each other. This pressure

often results in parts of furniture no longer fitting together closely or becoming distorted

or breaking from their own internal stresses.

The response to relative humidity changes begins with determining the annual average RH

for your particular space. Then try to keep the RH in the space where your furniture is as

close to that average as possible, generally within about 10% up or down. De-humidify in

the summer and humidify in the winter.

Be aware that raising the temperature lowers the humidity and vice versa. Thus, modern

heating systems, which can drive down interior RH in the winter, almost invariably cause

problems for furniture. To counteract their effect, you can either modify the RH by keeping

furniture containing spaces cooler in the winter or most importantly, have a good working

humidifier for your home. A humidistat automatically works to balance the humidity in

your home so it is constant. Dry indoor air can suck enough moisture from its surroundings

to do permanent damage to wood, causing it to crack or split.

Remember, that not all woods are created equal. Two factors that help determine how

rapidly a wood will lose moisture are pore size and surface hardness. A piece made from a

dense and hard wood will dry less rapidly than pieces made from softer woods.

Furniture that is sealed and lacquered will lose moisture more slowly than an unfinished

piece while pieces with veneer finishes are not only stronger, but lose moisture more

slowly than other finishes.

To help protect your wood furniture, take these steps:

Use a humidifier, preferably one with an automatic control system that can sense the

humidity level and adjust itself accordingly. Don't over-humidify; that can damage wood

by causing it to expand and contract.

Keep furniture out of direct sunlight, which can cause it to dry out, crack and warp.

If you can avoid it, don't put furniture near heating vents. If you must, keep the piece 3

to 4 inches away from the wall, giving the heat and air space to circulate.

Dust with soft dry cloth.

Do not use liquid or aerosol products.

CARE and MAINTENANCE

IMPORTANT

 : 

Please read this manual carefully before beginning

assembly of this product. Keep this manual for future reference.

Содержание MARANA AXCCMAR22


















Отзывы: