This product package includes:
• AC Power Inverter
• Cigar Plug Cable
• Battery Clamp Cable (CPS480PAU only)
• User Guide
Thank you for choosing a CyberPower power inverter. To enjoy all the
features and benefits of Inverter, please read and follow all instructions
completely.
The power inverter is a portable source of 120 volt AC power. The AC
Power converts DC battery power from your vehicle into standard 120
volt AC power, allowing you to power most notebook computers, cell
phone chargers, camcorders, and other electronic products drawing AC
power. Your personal devices may exceed the inverters wattage limit.
Refer to your device's user guide for actual wattage requirements.
This guide contains important information regarding the safety,
operation, maintenance, and storage of this product. Failure to read this
guide and follow the directions could result in injury and/or property
damage.
Before installing and using the CyberPower power inverter please read
the manual. Misusing or incorrectly connecting the Inverter may damage
the equipment or create hazardous conditions for users. Read the
following safety instructions and pay special attention to all
CAUTION
and
WARNING
statements in the manual.
1. 120 volt AC outlet
2. USB charging port
3. LED indicator light [Power LED(Green), Input / Output Fault (Red)]
4. ON/OFF Switch
5. DC Input positive terminal
6. DC Input negative terminal
7. Cooling Fan
Connecting the power cord for loads under 150 watts
Follow these steps to connect the power inverter :
1. Place the inverter on a flat surface in your vehicle floor.
2. Make sure the power switch on the panel is off.
3. Take the power cord equipped with the cigar plug and place the ring
terminals over the two cabling terminals on the back of the inverter.
4. Place the inverter cigar plug in the vehicle cigarette lighter socket.
5. Turn on the power switch. The green light indicates that the inverter is
operating normally and that AC power is available at the outlet.
6. Verify that the connected device(s) draws less than 150 watts and plug
into the AC outlet.
7. Always turn the inverter off when not in use.
Connecting the power cords for loads over 150 watts
Follow these steps to connect the power inverter :
1. Place the inverter on a flat surface.
2. Make sure the power switch on the panel is off.
3. Take the power cord equipped with battery clamps on one end and
place the ring terminals over the two cabling terminals on the back of
the inverter.
4. Fasten the positive (red) clamp to the positive battery post, and then
fasten the negative (black) clamp to the negative battery post.
5. Turn on the power switch. The green light indicates that the inverter is
operating normally and that AC power is available at the outlet.
6. Take device power cord plug into the inverter AC outlet.
7. Always turn the inverter off when not in use.
Make sure you connect cable red to red and black to black, and make
sure you screw the nuts on tightly.
Use the cigar plug cable only when the vehicle’s engine is running.
Use the cigar plug cable with the engine off will cause excessive
battery drain.
• Do not operate the inverter near flammable materials, fumes, or
gases.
• Always use the inverter where there is adequate ventilation. Do not
obstruct the ventilation slots.
• Never immerse the unit in water or other liquids.
• Proper cooling is essential when operating the inverter. Refrain from
placing the inverter near the vehicle's heat vent or in direct sunlight.
• Always turn the inverter off by removing it from the DC accessory
socket when not in use.
• Check the warning labels on battery chargers or adapters before
connecting them to the inverter. Do not connect battery chargers or
adapters with warnings about using with inverters.
CAUTION :
1. Connect the RED cable to the
POSITIVE terminal of the battery.
2. Connect the BLACK cable to the
NEGATIVE terminal of the battery.
A reverse polarity connection (positive to negative) will blow a fuse in
the inverter and may permanently damage the unit. Damage caused
by a reverse polarity connection is not covered by your warranty.
Batteries contain corrosive materials and present an electrical shock
hazard. To prevent irritation and burns, wear protective eyewear and
clothing when you install the inverter or work with the batteries.Take
special care to ensure that metal tools and personal metal objects like
rings and bracelets do not contact the battery terminals.
CAUTION
WARNING
CAUTION
Battery
Red
Black
(+)
(-)
CAUTION :
1. Connect the RED cable to the
POSITIVE terminal of the inverter.
2. Connect the BLACK cable to the
NEGATIVE terminal of the inverter.
CPS240PAU
CPS480PAU
Front View
Back View
Front View
Back View
1
1
2 3
4
7
5
6
4
240 User Guide
480 User Guide
AC Mobile Power Inverters
Introduction
Product Overview
Package Contents
Product Features
Operation - CPS240PAU / CPS480PAU cigar plug cable
Operating and Storage Tips
Operation - CPS480PAU only
1
2
3
7
5
6
Operating Tips
The inverter should only be operated under the following conditions:
• Dry - Do not allow water or other liquids to come into contact with the
inverter.
• Moderate Temperature - Ambient air temperature should be between
32
o
F - 104
o
F (0
o
C - 40
o
C). Keep the inverter out of direct sunlight.
• Free Air Flow - Keep the inverter's ventilation slots unobstructed to
ensure air flow to the unit. Do not place any items on or over the inverter
during operation. The unit will shut down if it overheats.
Storage Tips
• Proper storage temperature range is 32
o
F - 122
o
F (0
o
C - 50
o
C)
• Store and use the inverter in a cool and dry environment.
• Avoid exposing the inverter to heating elements, direct sunlight, or high
humidity.
TM
TM
CPS240PAU
CPS480PAU
