Spring
Decorative Ring
Contact Pin
Contact Retainer
15 ampFuse
12V DC Adapter
Problem
No AC output -
Red LED lit.
No AC output -
Green LED not
lit.
Motorized power
tool will not
operate
1.DC input is below 11
Vdc / Over 15Vdc
2.Short circuit.
3. Overload
4. Inverter hot.
1.Bad connection or
wiring
2.Fuse is blown
Excessive startup load.
If the start up load
exceeds the inverters
peak load capability it
will not work.
1.Check your battery volts
and recharge or replace the
battery.
2. Disconnect the load.
3. Reduce the load.
4. Disconnect the load and
operate the inverter for a
few minutes.
1.Tighten all DC connections.
2.Check fuse and replace or
Call Service
Disconnect the load until the
inverter operates normally
and connect the load again.
Suggested Solutions
Possible Cause
Figure 1. Fuse Replacement
K01-0000377-01
Note Page
Model
Input Voltage
Output Peak Power
Output Continuous Power
Output Voltage
Output USB Voltage
Output Frequency
Output Waveform
Input Fuse (Internal)
Input Fuse (Cigar plug)
Protection Features
CPS240PAU CPS480PAU
11 to 15 volts
240 Watts 480 Watts
200 Watts 400 Watts
120 Volts
5 Volts
60 Hz
Simulated Sine Wave
25Amp 25Amp x2
15Amp (CPS480PAU only)
Overload, Overvoltage,
Overheating, Short-circuit
DC Fuse Replacement (For Cigar Plug Cable)
Specifications
Troubleshooting
The CPS480PAU inverter contains a fuse inside in the cigar plug (see
Figure 1) to protect the unit against overloading. If the inverter draws
more than 150 watts, the internal fuse may open to protect the inverter,
vehicle battery, and the connected equipment. To replace the fuse, please
follow the instructions below:
1. Unplug the inverter from the power source.
2. Remove the contact retainer from the 12V DC adapter.
3. Replace the 15 amp fuse.
4. Reassemble the fuse, contact pin, and contact screw carefully.
5. Ensure all pieces shown in Figure 1 are installed in the correct
sequence.
CyberPower Systems (USA), Inc.
4241 12th Avenue East, Suite 400, Shakopee, MN 55379
TEL: (952) 403-9500 Toll-Free: (877) 297-6937
FAX: (952) 403-0009 E-mail: [email protected]
CPSww.com
C
2014 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
Limited Warranty
Product Registration
Technical Support
Legal notices (FCC Part 15)
CyberPower warrants this CPS240PAU / CPS480PAU (the "Inverter") to be free from
material and manufacturing defects for two years. If a defect results in product failure
during its normal use, CyberPower’s sole responsibility is to repair or replace (at its
sole option) the Inverter.
The foregoing Limited Warranty is the consumer’s sole and exclusive remedy and
excludes any incidental or consequential damages. Some States do not allow the
exclusion or limitation of incidental and consequential damages, so certain of the
above limitations or exclusions may not apply to you (the Consumer). This limited
warranty gives the Consumer specific legal rights and the Consumer may have other
rights, which vary from State to State.
To make a Limited Warranty claim:
1. Pack and ship the Inverter to CyberPower at 4241 12th Avenue East, Suite 400,
Shakopee, MN 55379.
2. Clearly indicate on the outside of the packaging that this is a “WARRANTY
RETURN”
3. Clearly include your name and address (a) on the outside packaging and (b) on a
sheet of paper enclosed in the box with the Inverter that is being returned.
4. You MUST prepay all shipping costs and you are responsible for packaging and
shipment.
CAUTION:
Any changes or modifications not expressly approved by the guarantee
of this device could void the user’s authority to operate the equipment.
Thank you for purchasing a CyberPower product. Prompt product registration entitles
coverage under the Limited Warranty and also allows the opportunity to be notified of
product enhancements, upgrades, and other announcements.
Registration is quick and easy at www.cpsww.com/register
Feel free to contact our Tech Support department with installation, troubleshooting, or
general product questions.
CyberPower Technical Support
Phone: 1-877-297-6937
Email: [email protected]
Web: www.CPSww.com
Address: 4241 12th Ave. E., STE 400, Shakopee, MN 55379
Hours of Operation: Monday – Friday, 7:00am – 6:00pm (CST)
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the
equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for
help. Any special accessories needed for compliance must be specified in the instruction.
CAUTION:
A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is essential that only the
supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
