CyberPower PDU33 Series Скачать руководство пользователя

Страница: 95 / 96

3-Phase Intelligent PDU User Guide

Firmware Upgrade

scp <filename> <user>@<

IP address of PDU>:

Note:

(5) The SSH setting on the PDU must be Enabled.

(6)

is the filename of the firmware file. There are two firmware files to upload:

cpsmpdumbfw_XXX.bin

and

cpsmpdumbdata_XXX.bin

. In order to upgrade the firmware

version both files need to be uploaded. Only one firmware file can be uploaded at a time, it is

recommended to upload the firmware file

cpsmpdumbfw_XXX.bin

first followed by the data file

cpsmpdumbdata_XXX.bin

(7)

<user>

is the username of the SSH account on the PDU.

(8)

Ensure to add “

” after the IP address.

For example:

scp cpsmpdumbfw_XXX.bin [email protected]:

Note:

cpsmpdumbfw_XXX.bin

is the firmware file of the version being updated.

4. After executing the command, a message may appear asking if you trust the host. To continue type

” for yes within 10 seconds.

5. On the next screen enter the PDU password. The firmware file transfer may take a couple minutes

to complete. Please wait until the progress indicator displays 100%. The system will automatically

log out and reboot after the transfer is complete.

6. Repeat steps 3 through step 5 to upload the data file

cpsmpdumbdata_XXX.bin

to complete the

firmware update process.

7. If the firmware file transfer is unsuccessful you will see an error message. Attempt to retype the

command and execute it again.

Содержание PDU33 Series
































































































Результаты поиска

Содержание PDU33 Series

Отзывы:

Похожие инструкции для PDU33 Series

Бренды по названию

Популярные бренды

CyberPower PDU33 Series, Руководство пользователя

Результаты поиска

Содержание PDU33 Series

Отзывы:

Похожие инструкции для PDU33 Series

Бренды по названию

Популярные бренды