manualshive.com logo in svg

CyberPower OLS10000ERT6UA, Руководство пользователя, Страница: 33 / 39

Поделиться
Скачать
CyberPower OLS10000ERT6UA Скачать руководство пользователя страница 33

30

TROUBLESHOOTING

PROBLEM 

DISPLAYED

POSSIBLE CAUSE

SOLUTION

EPO Active

EPO connector is open

Check the EPO connector status

Site Fail

The Ground wire is 

disconnected or Phase 

and neutral conductor at 

input of UPS system are 

reversed

Check the Ground wire status. 

Reverse mains power wiring.

Battery Open

Battery is disconnected

Do the battery test. 

Check the battery bank is connected to 

the UPS. 

Check the battery breaker is turned on.

Battery volt low

Battery voltage is low

When audible alarm sounding every 

second, battery is almost empty.

Over load

Overload

Check the loads and remove non-critical 

loads. 

Check if some loads are failed.

Fan Fail

Fan abnormal

Check if the fan is running normally.

Charger Fail

The charge fails

Consult dealer.

Battery Over 

Voltage

Battery voltage is higher 

than normal value

Check if the battery quantity is correct.

Over Charge

Battery is over charged

The UPS will turn off the charger until the 

battery voltage is normal

Amb NTC abnormal

The ambient temperature 

is too high

Check the environment ventilation.

Ambient NTC 

abnormal

UPS internal fault

Consult dealer.

Cable disconnect

The parallel cable is 

disconnected

Check the parallel cable.

Cable loss

The parallel cable is 

disconnected

Check the parallel cable.

Battery Differ

The battery packs 

of some UPS are 

disconnected

Check if all the battery pack is 

connected.

Line Differ

The mains input of some 

UPS is disconnected

Check the building wiring and input cable.
Check if the input breaker is closed.
Ensure the UPSs are connected to same 

input source.

Warning Indication 

Содержание OLS10000ERT6UA








































Отзывы:

Нет отзывов