CyberData RAL 9003 Скачать руководство пользователя

Страница: 39 / 126

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

2.2.4 Confirm the IP Address and Test the Audio

2.2.4.1 Reset Test Function Management (RTFM) Button

When the speaker is operational and linked to the network, use the Reset Test Function
Management (RTFM) button (

Figure 2-10

) on the speaker face to announce and confirm the

speaker’s IP Address and test that the audio is working.

Note

Using the RTFM button will lock the digital volume level to

and disable the analog volume

control dial.

Figure 2-10. RTFM Button

To announce a speaker’s current IP address, press and release the RTFM button within a five
second window.

Note

The speaker will use DHCP to obtain the new IP address (DHCP-assigned address or
default to 10.10.10.10 if a DHCP server is not present).

Note

Pressing and holding the RTFM button for longer than five seconds will restore the speaker
to the factory default settings.

RTFM button

Содержание RAL 9003































































































































Результаты поиска

Содержание RAL 9003

Отзывы:

Похожие инструкции для RAL 9003

Бренды по названию

Популярные бренды

CyberData RAL 9003, Руководство по эксплуатации

Результаты поиска

Содержание RAL 9003

Отзывы:

Похожие инструкции для RAL 9003

Бренды по названию

Популярные бренды