background image

 

plate and firmly tighten the swivel handle to hold the Hole Cutting Tool to the pipe. 

 

 

 

 

 

 

 

 

 

 

 

4. The base of the JK114 Hole Cutting Tool includes a level vial that can be used to align a 

series of holes. (as photo above) 

 

5. With one hand on the Hole Cutting Tool to stabilize and guide it, slightly loosen the swivel 

handle to allow final  positioning of the tool. Align the pilot drill  with the desired cut location, 

and  firmly  tighten  the  swivel  handle.  Do  not remove  your  hands  from  the  Hole  Cutting Tool 

until you have confirmed that it is securely attached to the pipe. The Hole Cutting Tool must 

be securely and squarely attached to the pipe to help reduce the risk of hole saw jamming. 

 
Operating Instructions 

Warning: eye protection, cutting injury and entanglement danger 

 

Always  wear  appropriate  eye  protection.  Cutting  tools  can  break  or  shatter.  Cutting 
produces chips that can be thrown or fall into eyes. Do not use for hot tapping. When 
cutting  into  an  existing  system,  the  pipe  must  be  drained  and  depressurized  prior to 
cutting. This reduces the risk of electrical shock and other serious injury. Do not wear 
gloves or loose clothing when operating machine. Keep Sleeves and jackets buttoned. 
Do  not  reach  across  machine.  Clothing  can  be  caught  by  the  machine  resulting  in 
entanglement.  Keep  fingers  and  hands  away  from  rotating  chuck  and  saw.  This 
reduces the risk of entanglement and cutting injuries. Follow operating instructions to 
reduce  the  risk  of  injury  from  electrical  shock  entanglement,  crushing  and  other 
causes and prevent Hole Cutter damage. 

 

1.  Confirm  that  the  Hole  Cutting  Tool  and  work  area  are  properly  set  up  and  that  the  work 

area is free of bystanders and other distractions. 

2. Assume a proper operating position that will allow: 
• Control of the Hole Cutting Tool, including the ON/- OFF switch and the feed handle. Do not 

turn the tool ON yet. 
• Good balance. Be sure that you do not have to over reach. 

 

 

Содержание JK114










Отзывы: