CustomWorks 0918, Руководство пользователя

Страница: 9 / 16

Bag K Bag K
Bag K Bag K Bag K
Fuel Tank / Motor Mounts Fuel Tank / Motor Mounts
Fuel Tank / Motor Mounts Fuel Tank / Motor Mounts Fuel Tank / Motor Mounts
1:1 -Parts for
Step#1
4350 Qty 1
Fuel Tank 5290 Qty 8
M3 x 8MM SH Screw 3270 Qty 2
Motor Mount 3262 Qty 1
Pipe Mount 5263 Qty 3
4-40 x 3/8 FH Screw
STEP #1
- Attach the 4450 Fuel Tank to the chassis using the
5264 Screws.
- Mount the 3270 Motor Mounts using the 5290 Motor
Mount Screws. The slanted edge of the mount will face
toward the spur gear.
- Mount the 3262 Pipe Mount using the 5264 Screws
and 5205 Nuts.
-Thread the XXXX Set Screw into the pipe mount, this
will be used to secure the wire coming from your
exhaust pipe to the car.
NOTE: The extra 5290 screws are to mount your nitro
motor after completion of the Clutch Bag.
1:1
5217 Qty 2
4-40 Lock Nut
1:1
5264 Qty 2
4-40 x 1/2 FH Screw
5264
5282
5217
5263
5290
4350
3270
5282 Qty 1
4-40 Set Screw
Servo and Linkage Installation Servo and Linkage Installation
Servo and Linkage Installation Servo and Linkage Installation Servo and Linkage Installation
5201 Qty 1
2-56 x 1/2 SH Screw
-Parts for
Steps
#1&#2
5242 Qty 1
Large Servo Saver
-Parts for
Step#3
1:1
8130 Qty2
Small Ball Cup 5281 Qty1
4-40 Stud
1:1
-Parts for
Step#4
5246 Qty1
Carb Ball Cup 5246 Qty2
Spring
5246 Qty1
Steel Snap 5228 Qty1
Throttle Rod (SHORT)
5215 Qty1
2-56 Ball End 5215 Qty1
2-56 Pivot Ball 5232 Qty1
2-56 Cone Spacer 5246 Qty2
Fuel Tubing 5252 Qty 1
4-40 x 1/4 BH Screw
1:1
5253 Qty 8
4-40 x 3/8 BH Screw
1:1
5263 Qty 9
4-40 x 3/8 FH Screw 8122 Qty 2
Ball Stud
5240 Qty4
Servo Mount
5282 Qty 5
4-40 Set Screw 5246 Qty5
Collar 5246 Qty1
Swivel
5246 Qty1
Servo Horn
5204 Qty 1
2-56 Lock Nut
5228 Qty1
Brake Rod (LONG)
1:1
STEP #1
- Attach 5240 Servo Mounts to your steering servo in the
position shown using 5253 Screws. ALSO do this for throttle
servo in the same position as well now.
- Thread 8122 Ball Stud into the upper-most center hole in the
5242 Servo Saver using the 3234 Spacer.
- Attach both 8130 Ball Cups to one another using the 5281
Stud until the Ball Cups bottom out on one another. Snap a
Ball Cup onto the Ball Stud on the Servo Saver.
- Determine which of the Spline Inserts are correct for your
servo by pressing it over the drive on the servo. Align the
servo so it has equal throw in both directions.
- Press the Servo Saver onto the Spline Insert so that the Servo
Saver is perpendicular to the servo, attach using the screw
that came with your servo.
STEP #2
- Mount the servos to the chassis using 5263 Screws as
shown.
- Thread the 8122 Ball Stud into the top of the Steering
Slide, Snap the Ball Cup onto the Ball Stud.
-Using double sided tape, mount your reciever to the
top of the steering servo.
- Attach 3209 Antenna Mount in either of the two
holes shown below.
NOTE: Steering movement should be bind free except
for the restriction of the servo transmission.
3209 Qty1
Antenna Mount
Bag J Bag J
Bag J Bag J Bag J
Bag K Bag K
Bag K Bag K
Bag K
5240
5253
5242
8130
5281
8122
8130
5263
3209
8122
3234 Qty 2
Spacer
3234
- 3234 SPACER IN STEPS 1&2 USED
TO LEVEL THE DRAG LINK WITH
DIFFERENT SERVOS.
- 3234 SPACER IN STEPS 1&2 USED TO LEVEL
THE DRAG LINK WITH DIFFERENT SERVOS.
3262
3234