manualshive.com logo in svg

CustomWorks 0918, Руководство пользователя

Поделиться
Скачать
CustomWorks 0918 Скачать руководство пользователя страница 5

Rear Suspension

Rear Suspension

Rear Suspension

Rear Suspension

Rear Suspension

7216       Qty 2
Rear CVD Axle

7211      Qty 2
CVD Coupling

4235                  Qty 2
Rear Outer Susp Pin

-Parts for
 Step#1

7214             Qty 2
Medium Dogbone

3241      Qty 2
Bearing Carrier

1:1

XXXX     Qty 4
Ball Stud

-Parts for
 STEP#2

1:1

5230   Qty 24
E-Clip

-Parts for
 STEP#3

1255      Qty 10
Spacer

1:1

7211     Qty 2
Rear CVD Pin

7211       Qty 2
CVD  Set Screw

7203   Qty 2
Roll Pin

5223                  Qty 2
1 3/4” TI Turnbuckle

5235          Qty 4
Ball Cup

1:1

5217     Qty 2
4-40 Lock Nut

1226      Qty 4
Ball Bearing

1:1

1:1

7047      Qty 8
Spacer

- Press 1226 Ball Bearings into the 3241 Bearing Carrier.
- Attach the Bearing Carrier to the Susp Arm using 4235
  Susp Pin with (2) 1255 Spacers on each side of the
  Bearing Carrier.
- NOTE: The Suspension Pin will pass thru the UPPER
  hole in the Bearing Carrier.
- Retain the Susp Pin using 5230 E-Clips.

- Apply grease to the areas shown.
- Apply thread-lock (Loctite) to the set screw.
- Align the holes as shown so that the
 7211 CVD Pin can pass thru the Bone,
 Axle, and Coupling. Pin should be evenly
spaced in the DogBone.
-Tighten the Set Screw by angling the Bone
 and Axle so the set-screw is able to be tightened.

LOCTITE

GREASE

STEP #2

4235

5230

1226

STEP #1

1255

3241

8122         Qty 4
Ball Stud

STEP #3

- Slide (4) 7047
Shims onto the
axle and retain
using the 7203
Roll Pin. Pin should
be evenly spaced
in Axle.

5217

7211
(Pin)

7214

7216

7211
   (Coupling)

7211
(Set Screw)

1255

8122

7203

7047

Bag D

Bag D

Bag D

Bag D

Bag D

1:1

8122

- Slide a 1255 Spacer onto
the Ball Stud and thread
into the Bearing Carrier in
the outer most hole.

- Assemble the camber links by threading
the 5235 Ball Cup on each end of the
5223 Turnbuckle. Attach by snapping the
Ball Cups onto the Ball Studs.

- Slide the thick shim packaged
with the CVD parts onto the CVD
Axle, Insert the CVD assembly by
sliding the axle thru the bearings.

7214 MEDIUM BONE

7214

5225

- Attach the 8122 Ball
Stud to the Rear
Bulkhead as shown
using a 5217 Lock Nut.

5225

- Add or remove 7047
Shims if necessary so
wheel spins freely when
tightened down.

Содержание 0918

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды