CUSTOM CARE CCUF-844 Скачать руководство пользователя

Страница: 8 / 36

CLEAN WATER REGENERATION WITH AUTOFLUSH

For installations with a high fouling potential, a back flush surge tank and/or a Separate Source Regeneration Valve (SEPS) or

three way valve on the inlet is recommended . During regeneration the three way valve will close the normal service inlet and

open the inlet from the back flush surge tank . The back flush surge tank supplies clean, treated water for regeneration . A 50

gallon (total volume) Pressure Tank is advisable . This is the minimum needed tank size to perform a treated water backwash .

For systems with AutoFlush, follow the instructions accompanying the NHBP . Make sure the drain receptacle can adequately

handle the flow from this line .

CLEAN WATER REGENERATION AND AUTOFLUSH

RAW WATER

INLET

NO HARD

WATER BYPASS

(#CV3070FM)

EXPANSION

TANK

FRESH

WATER TANK

MICRON

FILTER

CHECK

FRESH

WATER TANK

EXPANSION

TANK

TREATED

WATER

OUTLET

TREATED

WATER

OUTLET

No Hard Water Bypass

(#CV3070FM)

*Wires reversed for AutoFlush

RAW WATER

INLET

NO HARD

WATER BYPASS

NO HARD

WATER BYPASS

(AutoFlush)

(#CV3070FM)

EXPANSION

TANK

FRESH

WATER TANK

TREATED

WATER

OUTLET

Overhead View

CAUTION:

This backflush surge tank must be sized to provide enough water for the entire regeneration

whether an auto flush kit is installed or the chlorine generator option is used.

NOTE:

When a NHWB is used in an AutoFlush installation, it is necessary to reverse the wires

connected to the board. See the "Configuring Wires for AutoFlush Connection" section for

instructions to confirm or change the wire orientation.

*See additional programming settings section on pages 29-30 of this manual for more information regarding this installation.

The following parts are required for the listed

installations but are not included with the unit.

• Lower tank shut-off valve

• Spring Assisted check valve (see drawing

for location)

• No Raw Water Bypass x2 (CV-3070FM)

– For Clean Water Regen

– For AutoFlush (wires reversed)

INSTALLATION

Содержание CCUF-844





































Результаты поиска

Содержание CCUF-844

Отзывы:

Похожие инструкции для CCUF-844

Бренды по названию

Популярные бренды

CUSTOM CARE CCUF-844, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание CCUF-844

Отзывы:

Похожие инструкции для CCUF-844

Бренды по названию

Популярные бренды