Cushman 622020-L Скачать руководство пользователя страница 75

Страница: 75 / 84

5 - 25

MAINTENANCE

Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.

FUEL SYSTEM



Check for leaks at tank, cap, system lines, filters, pump, carburetor



Check system lines for cracks/deterioration

THROTTLE/GOVERNOR LINKAGE



Check operation and governed speed

HARDWARE AND FASTENERS



Check for loose or missing hardware and components



Tighten or replace missing hardware

SEMI-ANNUAL - 125 HOURS

(includes items listed in previous tables & the following)

BATTERY



Clean battery & terminals

DIRECTION SELECTOR



Check for wear and smooth movement (lubricate shaft with light oil if required)

KING PINS



Check for excessive play and tightness of retaining nuts

STEERING ASSEMBLY



Check bellows and pinion seal for damage or grease leakage

RACK END BALL JOINT



Lubricate, use wheel bearing grease

REAR AXLE



Check for unusual noise and loose or missing mounting hardware

AIR FILTER ELEMENT



Check filter element, clean/replace as required

OIL FILTER



Replace (at oil change)

ENGINE OIL



Replace with SAE 10W-30 or 10W-40 that meets or exceeds SF, SG, CC oil,

DO NOT OVERFILL

DRIVE BELT



Check for cracks, fraying and excessive wear

ANNUAL - 250-300 HOURS

(includes items listed in previous tables & the following)

FRONT WHEEL BEARINGS



Check and adjust as required, see Technician’s Repair and Service Manual

REAR AXLE



Check lubricant, add lubricant as required

SERVICE BRAKES



Clean and adjust, see Technician’s Repair and Service Manual



Check brake shoe linings, see Technician’s Repair and Service Manual



Check level, add if required (DOT 3) and check for leakage

FUEL FILTER



Replace

SPARK PLUG



Replace, gap new plug

MUFFLER/EXHAUST



Check mounting hardware; check for leaks at head and muffler gaskets

VALVES



Check cold (intake/exhaust) per Technician’s Repair and Service Manual

500 HOURS

(includes items listed in previous tables & the following)

CARBURETOR



Clean

CYLINDER HEAD AND PISTON



Remove carbon from cylinder head and piston



Check valve seats for carbon buildup and clean as required

Periodic Service Schedule

Содержание 622020-L





















































































Результаты поиска

Содержание 622020-L

Отзывы:

Похожие инструкции для 622020-L

Бренды по названию

Популярные бренды

Cushman 622020-L, Руководство пользователя

Результаты поиска

Содержание 622020-L

Отзывы:

Похожие инструкции для 622020-L

Бренды по названию

Популярные бренды