Cushman 2007 COMMANDER 2100, Руководство пользователя и руководство по обслуживанию

Страница: 38 / 64

OPERATION AND SERVICE INFORMATION
Page 20
Owner’s Manual and Service Guide
Read all of Manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings
Fig. 24 Torque Specifications and Bolt Grades
Batteries are heavy. Use
proper lifting techniques
when moving them. Always
lift the battery with a com-
mercially available battery
lifting device. Do not tip bat-
teries when removing or
installing them; spilled elec-
trolyte can cause burns and damage.
The electrolyte in a storage battery is an
acid solution which can cause severe burns
to the skin and eyes. Treat all electrolyte
spills to the body and eyes with extended
flushing with clear water. Contact a physi-
cian immediately.
Always wear a safety shield or
approved safety goggles when
adding water or charging batter-
ies.
Any electrolyte spills should be neutralized
with a solution of 1/4 cup (60 ml) sodium
bicarbonate (baking soda) dissolved in 1 1/2
gallons (6 liters) of water and flushed with
water.
Overfilling batteries may result in electrolyte
being expelled from the battery during the
charge cycle. Expelled electrolyte may
cause damage to the vehicle and storage
facility.
Aerosol containers of battery terminal pro-
tectant must be used with extreme care.
Insulate metal container to prevent can from
contacting battery terminals which could
result in an explosion.
Wrap wrenches with
vinyl tape to prevent
the possibility of a
dropped wrench from
‘shorting out’ a battery, which could result in
an explosion and severe personal injury or
death.
BATTERY
A battery is defined as two dissimilar metals immersed in
an acid. If the acid is absent or if the metals are not dis-
similar, a battery has not been created. The batteries
most commonly used in these vehicles are lead acid.
A battery does not store electricity, but is able to produce
electricity as the result of a chemical reaction which
ALL TORQUE FIGURES ARE IN FT. LBS. (Nm)
BOLT SIZE
Grade 2
1/4" 5/16" 3/8" 7/16" 1/2" 9/16" 5/8" 3/4" 7/8" 1"
Unless otherwise noted in text, tighten all hardware in accordance with this chart.
This chart specifies 'lubricated' torque figures. Fasteners that are plated or lubricated when
installed are considered 'wet' and require approximately 80% of the torque required for 'dry' fasteners.
4
(5)
8
(11)
15
(20)
24
(33)
35
(47)
55
(75)
75
(102)
130
(176)
125
(169)
190
(258)
Grade 5
Grade 8
6
(8)
13
(18)
23
(31)
35
(47)
55
(75)
80
(108)
110
(149)
200
(271)
320
(434)
480
(651)
6
(8)
18
(24)
35
(47)
55
(75)
80
(108)
110
(149)
170
(230)
280
(380)
460
(624)
680
(922)
BOLT SIZE
Class 5.8
(Grade 2)
M4 M5 M6 M8 M10 M12 M14
1
(2)
2
(3)
4
(6)
10
(14)
20
(27)
35
(47)
55
(76.4)
Class 8.8
(Grade 5)
2
(3)
4
(6)
7
(10)
18
(24)
35
(47)
61
(83)
97
(131)
Class 10.9
(Grade 8)
3
(4)
6
(8)
10
(14)
25
(34)
49
(66)
86
(117)
136
(184)
5.8
8.8
10.9
Ref Tsp 1