X
Y
2"
(5 cm)
min.
2"
(5 cm)
min.
5
#3 - ASSEMBLE RADIATOR
12
050012
PLASTIC
3/4"
1
CAP
(1.9 cm)
26
190026
ALUMINUM
7/8"
2
BRACKET
(2.2 cm)
28
190028
ALUMINUM
2
HALF WASHER
87
014387
SS/NYLON
8-32
2
LOCK NUT
231
010231
SS MACHINE
8-32 x 1-3/4"
2
SCREW
(4.4 cm)
410
030410
SS WORM
1"
6
CLAMP
(2.5 cm)
411
030411
SS WORM
1-1/4"
1
CLAMP
(3.2)
412
030412
SS WORM
1-1/2"
1
CLAMP
(3.8 cm)
413
030413
SS WORM
1-3/4"
1
CLAMP
(4.4 cm)
BA
BASE
1
ASSEMBLY
BB
ALUMINUM
1-1/4" x 48
1
TUBE
(3.2 x 121.9 cm)
BC
ALUMINUM
1" x 48"
1
TUBE
(2.5 x 121.9 cm)
BD
ALUMINUM
7/8" x 5"
1
TUBE
(2.2 x 12.7 cm)
BE
ALUMINUM
7/8" x 16"
2
TUBE(2.2 x 40.6cm)
BG
ALUMINUM
3/4" x 48"
1
TUBE
(1.9 x 121.9)
BH
ALUMINUM
5/8” x 6-1/2”
1
TUBE
(1.6 X 16.5 cm)
BI
ALUMINUM
5/8” x 7-3/4
1
TUBE
(1.6 x 19.7 cm)
CT1
10/12 M
1
TRAP
CT2
15/17 M
1
TRAP
CT3
20/30 M
1
TRAP
XHR
ALUMINUM
3/16" x 36"
2
ROD
(.5 x 91.4 cm)
KEY P/N DISPLAY DESC SIZE QTY
NOTE: When installing BE
tube, ensure at least 2" (5
cm) length of the adjoining
3/4" (1.9 cm) tubes are
inserted into R7000BE
(Figure A, points X and Y).
Place worm clamp (413) over top end of base assembly (BA). Note
Figure G for proper positioning of all worm clamps. Slide section BB
into BA 4 inches and secure worm clamp. Place worm clamp (412)
over slots of section BB. Slide section BC into BB 4 inches and secure
worm clamp. Attach capacity hat rods (XHR) to BC using hardware
shown in Figure G. Place worm clamp (411) over slots of section BC.
Before sliding Trap CT1 into BC, insert tube BH into the the bottom
tube of CT1 and BI into the top tube of CT1. The screws holding the
XHR rods will keep tube BH in place. Hold trap assembly CT1 with
FIGURE
F
R7000
87
87
231
231
26
28
37
37
26
28
capped end up and slide bottom tube into section BC until it is stopped by
the XHR mounting screws and secure worm clamp. Place worm clamps
(410) over each end of section BD. Slide BD over CT1 top tube 2" and
secure worm clamp. Hold trap assembly CT2 with capped end up and
slide bottom tube into BD 2" and secure worm clamp. Place worm clamps
(410) over each end of section BD. Slide BD over CT2 top tube 3" and
secure worm clamp. Hold trap assembly CT3 with capped end up and
slide bottom tube into BD 3-1/2". Secure worm clamp. Place worm clamps
(410) over each end of section BD. Slide BE over CT3 top tube 5”(12.7
cm) and secure worm clamp. Slide BG into BE 2" (5.1 cm) and secure
worm clamp. Install cap (12) . Verify all radiator dimensions to within 1/4"
(.6 cm) using Figure F.
Secure hose clamps about
1/4" from top of each slotted
tube to ensure adequate
compression.
FIGURE
G
Dimension A
10 / 12m
135"
(342.9 cm)
Dimension B
15 / 17 m
6"
(15.2 cm)
Dimension C
(20 / 30m)
18"
(45.7 cm)
Dimension D
(40m)
See Chart A
410
BG
12
410
BE
CT3
CT2
CT1
BD
BE
410
410
410
410
411
BC
412
BB
413
BA
Dimension D
Center Frequency
(in)
(cm)
(MHz)
53
134.5
7.300
54
137
7.275
56
142
7.225
58
147
7.175
60
152.5
7.125
62
157.5
7.075
64
162.5
7.025
65
165
7.000
Chart A
BE
BH
BI