CUSHCRAFT MA5B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 12

CUSHCRAFT MA5B Скачать руководство пользователя страница 11

6 - BOOM TO MAST ASSEMBLY

Before installing the antenna on the mast, check all hardware and worm
clamps to insure they are tight. Install the antenna on the mast as shown
in Figure 6. Using U-bolts (404), lock washers (19), and hex nuts (18),
fasten the antenna to the mast. Place the connector boot (115) on the coax
cable before assembly. Apply silicone sealant (116) to the threads of the
matching network RF connector and tighten the cable to the matching
network. Do not apply silicone to the center conductor or dielectric of either
connector. Slide the boot over the connector. Place the coaxial cable over
the top of element #2 on the boom and run the cable down the mast to the
radio equipment.

KEY P/N DISPLAY DESC SIZE QTY

18

010118

HEX NUT

5/16"

4

19

010119

LOCK WASHER

5/16"

4

115

050115

CONNECTOR

1

BOOT

116

240116

SILICONE

1

PACKAGE

404

010404

U-BOLT

5/16-18 x 2-1/2"

2

(6.4 cm)

MA5B

MAST

18

19

404

BOOM

4 PLACES

4 PLACES

2 PLACES

FIGURE 6

Page 10

«
...
9
10
11
12
»

Содержание MA5B













Отзывы:

Нет отзывов