Curtiss-Wright SSR/CHS/001/B Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 34

Curtiss-Wright SSR/CHS/001/B Скачать руководство пользователя страница 18

14 Multi-role Recorders User Guide (HW/BK/0034 | 12 Oct. 2021)

3

Status LEDs

The LOGGING LED lights green when recording is taking place.
When the ERROR LED lights yellow, recording is not possible. The ERROR LED lights yellow under the following

conditions:

•

The memory media is not inserted.

•

The memory media is not recognized or not mounted.

•

The memory media is being formatted.

•

The memory media is full and wraparound is disabled.

•

The Ethernet network is not connected. (Does not apply to an SSR/CHS/001/C.)

N

OTE

:

Even though the recorder is still recording packets on the backplane when the Ethernet input is discon

-

nected, it is regarded as an error condition. As an error condition, it is reported via the Error LED and

the REC_STATUS output signal on the I/O connector.

N

OTE

:

Multi-role recorders do not have a power on/off switch. Once power is connected, the multi-role recorder is

always on. If the display is not on, confirm power is connected.

If you connect power and the START/STOP switch is in the START position, the recorder attempts to begin

recording. For this reason, we recommend you ensure the START/STOP switch is in the STOP position

when you connect power.

«
...
16
17
18
19
20
...
»

Содержание SSR/CHS/001/B



































Отзывы:

Нет отзывов