Curtiss-Wright SAM/DEC/008 Скачать руководство пользователя

Страница: 11 / 12

SAM/DEC/008

19 Apr. 2016 | DST/Z/010

CURTISSWRIGHTDS.COM

Ordering information

PART NUMBER

DESCRIPTION

SAM/DEC/008

Ethernet based USB powered PCM decommutator

By default, a CON/USB/006 and an ACC/CON/012/00 cable are included with each SAM/DEC/008 card in the shipment. These

part numbers will be added to the Confirmation of Order unless an alternative option is specified (see the

Cables

data sheet). As

well as the CON/USB/006 and ACC/CON/012/00 cables, an ACC/ASY/022 cable is needed for use with a PCM controller
module; unless ordered, the ACC/ASY/022 is not included in the shipment.

Revision history

REVISION

DIFFERENCES

STATUS

SAM/DEC/008

First release

Recommended for new programs

Supporting software

SOFTWARE

DETAILS

DAS Studio 3

User interface for setup and management of data acquisition, network switches, recorders and ground
stations in an integrated environment

KSM-500

This module is supported by the KSM-500 suite of software tools

SWP/SDK/004

Software Development Kit for SAM/DEC/008

Содержание SAM/DEC/008













Результаты поиска

Содержание SAM/DEC/008

Отзывы:

Похожие инструкции для SAM/DEC/008

Бренды по названию

Популярные бренды

Curtiss-Wright SAM/DEC/008, Руководство пользователя

Результаты поиска

Содержание SAM/DEC/008

Отзывы:

Похожие инструкции для SAM/DEC/008

Бренды по названию

Популярные бренды