Curtiss-Wright KAD/ADC/129/S2 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 12

Curtiss-Wright KAD/ADC/129/S2 Скачать руководство пользователя страница 12

KAD/ADC/129/S2

12

1 Jun. 2021 | DST/V/081

CURTISSWRIGHT.COM

© 2021Curtiss-Wright. All rights reserved. Specifications are subject to change without notice.
All trademarks are the property of their respective owners.
This document was reviewed on 14/10/2020 and does not contain technical data.

Ordering information

By default, the standard mating connector, CON/KAD/002/CP, is included with each module in the shipment. Its part number
will be added to the Confirmation of Order unless an alternative option is specified (see the

Cables

data sheet).

The KAD/ADC/129/S2 uses power from the ±7V power line for excitation and therefore cannot be used with KAM/CHS/04L,
KAM/CHS/05F, KAM/CHS/03F, or KAM/CHS/02F.

Revision history

Supporting software

Related documentation

PART NUMBER

DESCRIPTION

KAD/ADC/129/S2

Full-bridge ADC (voltage excitation, programmable analog gain, sense lines, 25kHz b/w) - 4ch at
100ksps

REVISION

DIFFERENCES

STATUS

KAD/ADC/129/S2

First release

Recommended for new programs

SOFTWARE

DETAILS

KSM-500

This module is supported by the KSM-500 suite of software tools

DOCUMENT

DETAILS

DOC/DBK/001

Acra KAM-500 Databook

DOC/HBK/002

Environmental Qualification Handbook

DOC/MAN/018

KSM-500 Databook

DOC/MAN/030

DAS Studio 3 User Manual

TEC/NOT/001

Strain gages and ideal bridges

TEC/NOT/016

Power dissipation

TEC/NOT/049

Power estimation

«
...
10
11
12

Содержание KAD/ADC/129/S2













Отзывы:

Нет отзывов