Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 75 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

CANopen

The CANopen circuit is optically isolated from the drive main power as

well as other IO power.

There are two methods of connecting to the Tritex with the CANopen

option. If the COP option from model mask is chosen a single five pin

12 mm connector (Turck FS 57-.1) will be presented to the user for

connection or “T-ing”.

If the CON is chosen no connectors are provided, user wiring can be

passed through the cable gland or NPT port and inserted into connectors

on the termination board, see below. A 120

resistor is installed from

the factory, in CONN 1 pins 4 & 5, as a termination resistor and can be

removed for daisy chaining or changed to another value if desired.

*NOTE: Follow wiring of SIO board for IO and RS485 communications.

CON Option

Function

CONN 1

Terminal #

CAN H

CAN L

CAN H

CAN L

CONN 1

PIN 1

120

Ω

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды