manualshive.com logo in svg

Curtiss-Wright EXLAR GTX Series, Инструкция по установке и обслуживанию

Поделиться
Скачать
Curtiss-Wright EXLAR GTX Series Скачать руководство пользователя страница 7

GTX Series Actuator Installation & Maintenance Instructions | 

7

www.exlar.com

 | 952.500.6200

GTX080: 6 mm Hex

GTX100: 8 mm Hex

GTX080: 6 mm Hex

GTX100: 8 mm Hex

25 mm Long

30 mm Long

40 mm Long

50 mm Long

GTX080: Torque 12.2 Nm (9 ft-lbs)

GTX100: Torque 23 Nm (17 ft-lbs)

Figure 5 – 

Tapped face mount

3.2 MOUNTING CONSIDERATIONS

3.2.1 Actuator Alignment

IMPORTANT!

 Aligning the GTX Series actuator with respect to 

the load it is moving is critical. Any misalignment will decrease 

the life of the actuator’s components and may adversely affect 

application performance.

 

CAUTION!

 Excessive side load on the actuator output 

rod will dramatically reduce the life of the actuator and should be 
avoided. Side load can result from misalignment or loading that 
is not in line with the actuator output rod. 

Side-mounting notes:

GTX Series actuators include threaded holes in the faceplate 
and endplate. Exlar recommends using hardened fasteners to 
mount an actuator to your machine frame with an engagement 
depth of two times the screw diameter for tapped holes.

IMPORTANT! 

Tighten four cap screws to 12.24 Nm (9.0 ft-lb) 

max. Failure to properly tighten the screws can affect normal 

operation, damage the actuator and/or cause possible premature 
actuator failure.

3.2.2 Feedback Device Alignment

Every GTX Series actuator is mounted, aligned and tested using 

the customer-specified feedback device and amplifier (or an 
equivalent amplifier) to ensure proper feedback alignment and 

operation. Should an installed feedback device become mis-

aligned or there is a change in amplifier status, contact the Exlar 

factory to make arrangements to have the alignment readjusted.

Содержание EXLAR GTX Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды