5
Cold Brew Lock . . . (factory set to 5º )
Press
to select. Press
◄
or
►
to select the desired setting (5°F, 15°F or Off), then
to set and exit.
The Cold Brew Lock feature allows the brewer to brew at three different temperature levels from the actual set point. The first
setting is within 5 degrees of the set point, next is within 15 degrees of the set point, OFF is within 30 degrees of the set point
for the Ready to Brew message, however, it will brew at any temperature.
Master Reset
Press
to display Are You Sure?
Then
◄
for Yes,
►
for No. The brewer factory defaults are then reset.
Service Call (phone number factory set to 1-800-000-0000 x0000)
Press
to display the number and change a number. Press
◄
to move the number place and EX to exit when complete. This
number will be displayed during a heating system SENSOR ERROR or during a WATER ERROR.
Access Code (factory set to 1-2-3-4)
Press
to display the number and to change a number, (the number can be changed 1 to 4) or
◄
to move the number place
and EX to exit when complete.
Banner Name (factory set to CURTIS)
Press
to display letters and change letters or
◄
to move place and EX to exit when complete. This feature allows up
to 14 letters to be programmed for a company name or a regional name. Programming all blanks disables the Banner Name. If
programmed, the Banner Name is displayed every 5 seconds on and off.
P-Maintenance (factory set to OFF)
Press
to select. Set the number of gallons brewed to indicate P-Maintenance. Press
◄
or
►
to adjust from Off to 9500
gallons. This feature advances in 500 gallon increments. Press
to exit.
Beeper On/Off (factory set to ON)
Press
to display ON or OFF. Pressing either
◄
or
►
toggles between on and off. Press
to set and exit. When ON, this
feature allows you to hear a short beep each time a button is pressed.
Coffee Drip-out Mode (factory set to 2 minutes)
Press
to select. Press
◄
or
►
to move to the desired time (OFF, 1, 2, 3, 4, 5, 6, 7, 8 and 9 min.). Press
to set and exit.
Tea Drip-out Mode (factory set to OFF)
Press
to select. Press
◄
or
►
to move to the desired time (OFF, 1, 2, 3, 4 and 5 minutes). Press
to set and exit.
Displ. Brew Time (factory set to ON)
Press
to display ON or OFF. Pressing either
◄
or
►
toggles between ON and OFF. After Display Brew Time an EXIT
screen will return you to Brew Button Prog.
Display Messages (factory set to ON)
Press
to display ON or OFF. Pressing either
◄
or
►
toggles between ON and OFF. This feature allows the operator to
select the message “Rinse Server Before Brewing”. This message will be displayed any time the unit is not brewing.
Brew Button Program
This is the next group of options in the sequence. The screen will prompt you to choose tea or coffee. Coffee options are shown
below and on the following page. Tea options are shown on page 6.
Select Button
This is a temporary screen message indicating you are in the coffee brew button programming mode. Select a coffee brew but-
ton on the UCM.
Brew by Volume (factory settings: LARGE 200oz ±8oz. SMALL 64oz±4oz.)
Press
to select. The display will ask you to select a brew button, Large, Medium or Small. Press the desired brew button to
begin... when the desired volume is reached press the same brew button to stop the flow. Now the volume has been set.
Brew By Volume
Coffee
Drip-out Mode
Beeper On/Off
P-Maintenance
Banner Name
Access Code
Service Call
Master Reset
Cold Brew Lock
Displ. Brew Time
Tea
Drip-out Mode
Brew Button Prog
Select Button
Display Messages
Содержание CBHT
Страница 10: ...10 Electrical Schematic...
