Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CARRIAGE BOLT
1/2-13 x 1 1/2
4
1
HEX FLANGE NUT
HFN 1213
4
2
1/2" FISHWIRE
1_2 FISHWIRE
4
3
.250 x 1.00 x 2.50" SQUARE HOLE SPACER
CM-SP10
4
4
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING:
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3500
350
35
30
JEEP RENEGADE
3/31/2016
12142
60
Scan
for more
information
TOOLS REQUIRED
RATCHET
3/4", 21mm SOCKET
8" SOCKET EXTENSION
DIE GRINDER
TORQUE WRENCH
UTILITY KNIFE
UNIVERSAL JOINT SOCKET
OFFSET SCREWDRIVER
1.125"
3
1
4
2
1. Remove the rearmost rubber plugs on the bottom of each frame rail. Remove the forward most rubber plugs on the outside of each frame rail.
NOTE: For applications with a factory tow hook, remove the M14 bolts ins these locations using a 21mm socket. Skip to step 5.
2. Enlarge the rearmost hole with the die grinder on each frame rail to allow the carriage bolts and spacers to be inserted into the frame rail.
3. Clear away caulk as necessary near mounting holes on both sides using a knife.
4. Fishwire (1) 1/2" carriage bolts and (1) CM-SP10 into the forwardmost holes on the outside of each frame rail, leaving the fasteners in the
frame until hitch is in position. Reverse Fishwire (1) 1/2" carriage bolts and (1) CM-SP10 into the rearmost hole on the bottom of each frame
rail. Keep wires attached until hitch is raised into position.
5. Raise hitch into position, threading the Fishwires into the mounting holes. Remove Fishwire and loosely install 1/2" Hex Flange Nuts. NOTE: For
applications with a factory tow hook, loosely install factory M14 hardware.
6. Torque all 1/2" hardware to 110 ft.-lbs. NOTE: For applications with a factory tow hook, torque factory M14 hardware to 135 ft.-lbs.
DESIGNED FOR
USE WITH BALL
MOUNT #45521
EURO MOUNT
OPTION AVAILABLE
45571 (1 7/8" BALL)
45572 (2" BALL)
Hole Enlargement
No Drill
Part Removal
ENLARGE HOLE
FOR ACCESS
ENLARGE HOLE
FOR ACCESS
PASSENGER
FRAME RAIL
DRIVER FRAME RAIL
Содержание 12142
Страница 4: ......