Cumberland PNEG-240 Скачать руководство пользователя страница 58

Страница: 58 / 76

10. Parts List

PNEG-240

Chain Feeding System

1 Line Direct Drive Mini Hopper (C4920000-60 and C4920000-120) Parts List

Ref #

Part #

Description

Qty

C4920000-60

1 Line, 60 FPM Direct Drive

C4920000-120

1 Line, 120 FPM Direct Drive

7097730

1 Line Drive

HH-3008

Insert, Threaded 1/4"-20 Steel/Cadmium

S-1101

Bolt, HHCS 1/4"-20 x 1/2" ZN Grade 2

7097731

Power Shoe Wear Plate Assembly

S-248

Flat Washer 3/8" 7/16" I.D. 1" O.D. YDP

S-7185

Bolt, HHCS 3/8"-16 x 5/8" ZN Grade 2

C4000172-RD

Chain Stripper Assembly, Universal

S-7485

Flange Bolt 3/8"-16 x 1" JS500 Grade 8 or 8.2

S-1054

Lock Washer 3/8"

S-7489

Hex Nut 3/8"-16 JS500 Grade 5

7097522

Feed Return Wheel Shaft

7097609

Intake Wheel Weldment

S-7241

Cotter Pin 1/8" x 1-1/4" ZN Grade 2

7097514

1 Line Feed Return Wheel Slide

S-2041

Split Lock Washer 1/4" ZN

7098901

Feed Level Plate 1 Line 90°

S-6076

Carriage Bolt 5/16"-18 x 3/4" ZN Grade 2

S-845

Flat Washer 5/16" USS SAE YDP Grade 2

S-4301

Wing Nut 5/16"-18 ZN Grade 2

7097535

Drive Sprocket Cover Assembly

S-4330

Stud, Swage 1/4"-20 x 5/8" ZN

S-1102

Hex Nut 1/4"-20 ZN Grade 2

07097598A

Chain Guide with Hardware

7097737

Gearbox, Leedy, 52:1, Belt Drive, Right Hand (60 FPM)

7098744

Gearbox, Leedy, 37:1, Belt Drive, Right Hand (120 FPM)

S-3883

Bolt, HHTB 1/2"-13 x 1-3/4" YDP Grade 8

S-236

Split Lock Washer 1/2" REG ZN Plated

S-3729

Hex Nut 1/2"-13 YDP Grade 5

7097510

1 Line Drive Yoke Assembly

S-9169

Key, Square 1/4" x 1-1/2"

7097506

Drive Sprocket 3/8"

7099143

Drive Sprocket Collar

S-7371

Screw, Set 5/16"-18 x 1/2"

07097579A

Sheave, 0.750" Bore x 3" O.D. Double Groove

7098283

3/16" x 1-1/4" Key

7097544

Motor Mount Support Angle

7098748

Motor Mount

S-7086

Bolt, HHTB 5/16"-18 x 3" ZN Grade 2

7098223

Cap, Round, Fits 0.500-0.563 O.D., 0.500 HT

S-10268

Flange Nut 5/16"-18 JS500 Grade 5

S-5220

Nylock Nut 5/16" ZN Grade 5

DC-897

Decal, Cumberland Chain Feeder

DC-997

Decal, Danger Chain Sprocket

7099513

3/16" x 1-1/4" Shear Pin (Hard Grade)

Содержание PNEG-240













































































Результаты поиска

Содержание PNEG-240

Отзывы:

Похожие инструкции для PNEG-240

Бренды по названию

Популярные бренды

Cumberland PNEG-240, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PNEG-240

Отзывы:

Похожие инструкции для PNEG-240

Бренды по названию

Популярные бренды