background image

13

batches, the motor may overheat. If this happens, 
the processor will stop. Turn it off and wait for the 
motor to cool off before proceeding. It will usually 
cool off within 10 minutes. In extreme cases, it could 
take an hour.
Safety switches prevent the machine from operating 
when the work bowl or the cover is not locked into 
position. The motor stops within seconds when the 
motor is turned off, and a fast-stop circuit stops it 
instantly when the pusher assembly is unlocked.

CLEANING AND MAINTENANCE

Keep your Classic Series 14-Cup Food Processor 
ready to use on a kitchen counter. When it’s not 
being used, leave it unplugged.
Store the blade and discs as you would sharp knives 
– out of the reach of children. The Disc and Blade 
Holders, optional accessories, offer safe and  
convenient storage.
All parts except for the motor base are dishwasher 
safe, and we recommend washing them in the  
dishwasher. Insert the work bowl upside down. 
Remember where you place the sharp blade and 
discs, and unload the dishwasher carefully.
To simplify cleaning, rinse the work bowl, cover, 
pusher assembly and blade or disc immediately  
after use so food won’t dry on them. Openings at 
the bottom of the large pusher provide drainage and 
make cleaning easy. If food lodges in the pusher, 
remove it by running water through or by using a  
bottle brush.
If you wash the blade and discs by hand, do it  
carefully. Avoid leaving them in soapy water where 
they may disappear from sight. To clean the metal 
blade, fill the work bowl with soapy water, hold the 
blade by its plastic center and move it rapidly up 
and down on the center shaft of the bowl. Use of a 
spray attachment is also effective. If necessary, use 
a brush.
The work bowl is made of a plastic, which is shatter 
resistant and heat resistant. It should not be placed 
in a microwave oven.
Chopping certain foods may scratch or cloud the 
work bowl. Among them are ice, whole spices and 
oils like wintergreen. If you like to prepare your own 
spice blends, you may want to keep a second bowl 
just for that purpose.
The base housing is made of a tough plastic with 
high-impact resistance. Its smooth surface will look 
new for years. Keep a sponge handy as you work 
and wipe spills from the base.
Four rubber feet on the underside keep the base 
from moving on most work surfaces when the 
machine is processing heavy loads. If the feet leave 
spots on the counter, spray them with a spot  

remover and wipe with a damp sponge. If any trace 
of the spot remains, repeat the procedure and wipe 
the area with a damp sponge and non-abrasive 
cleaning powder.
To clean the inside of the detachable stem, slide the 
stem release bottom on the side up as far as it will go 
and hold it there as you run water through the stem.

IMPORTANT:

 Never store the blade or discs on the 

motor shaft. The blade or discs should not be placed 
on the shaft except when the processor is about to  
be used. Any other servicing should be performed 
by an authorized service representative.

MAINTENANCE: 

Any other servicing should be  

performed by an authorized service representative. 

 

FOR YOUR SAFETY

 Like all powerful electrical appliances, a Classic 
Series 14-Cup Food Processor should be handled 
with care. Follow these guidelines to protect you and 
your family from misuse that could cause injury.
•  Handle metal blade and discs carefully. Their  

cutting edges are very sharp.

•  Always place disc on flat, stable surface before  

connecting detachable stem.

•  Never put blade or disc on motor shaft until work 

bowl is locked in place.

•  Always be sure that blade or disc is down on 

motor shaft as far as it will go.

•  Always insert metal blade in work bowl before  

putting ingredients in bowl.

•  When slicing or shredding food, always use 

pusher. Never put your fingers or spatula into feed 
tube.

•  Always wait for blade or disc to stop spinning 

before you remove pusher assembly or cover from 
work bowl.

•  Always remove work bowl from base of machine 

before you remove metal blade.

•  Be careful to prevent metal blade from falling out 

of work bowl when emptying bowl. Remove it 
before tilting bowl, or hold it in place with your  
finger, a spatula or a spoon.

•  Do not use pusher assembly if sleeve becomes 

detached from pusher. Call Cuisinart Consumer 
Service immediately. Our toll-free number is listed 
in the warranty.

Содержание DFP-14NC Series
















Отзывы: