background image

17

S

ection

 5 — o

peration

8. 

Allow the engine to run for a few minutes at mid-throttle 

before putting the engine under load.

9. 

Observe the hour meter/indicator panel. If the battery 

indicator light or oil pressure light come on, immediately 

stop the engine. Have the tractor inspected by your Cub 

Cadet dealer.

Cold Weather Starting

When starting the engine at temperatures near or below 

freezing, ensure the correct viscosity motor oil is used in the 

engine and the battery is fully charged. Start the engine as 

follows:

1. 

Be sure the battery is in good condition. A warm battery 

has much more starting capacity than a cold battery.

2. 

Use fresh winter grade fuel. Winter grade gasoline has 

higher volatility to improve starting. Do not use gasoline 

left over from summer.

3. 

Follow the previous instruction for Starting the Engine.

Using Jumper Cables To Start Engine

WARNING! 

Batteries contain sulfuric acid and 

produce explosive gasses. Make certain the area is 

well ventilated, wear gloves and eye protection, and 

avoid sparks or flames near the battery.

If the battery charge is not sufficient to crank the engine, 

recharge the battery. If a battery charger is  unavailable and 

the tractor must be started, the aid of a booster battery will be 

necessary. Connect the booster battery as follows:

1. 

Connect the end of one cable to the disabled tractor 

battery’s positive terminal; then connect the other end of 

that cable to the booster battery’s positive terminal.

2. 

Connect one end of the other cable to the booster 

battery’s negative terminal; then connect the other end of 

that cable to the  frame of the disabled tractor, as far from 

the battery as possible.

3. 

Start the disabled tractor following the normal starting 

instructions previously provided; then disconnect 

the jumper cables in the exact reverse order of their 

connection.

4. 

Have the tractor’s electrical system checked and repaired 

as soon as possible to eliminate the need for jump starting.

Stopping the Engine

1. 

Place the PTO switch in the “OFF” position.

2. 

Engage the parking brake.

3. 

Move the throttle control to the SLOW 

 position and 

allow the engine to idle for about one minute.

4. 

Turn the ignition key to the “OFF” position and remove the 

key from the ignition switch.

NOTE: 

Always remove the key from the ignition switch to prevent 

accidental starting or battery discharge if the equipment is left 

unattended.

Driving The Tractor

WARNING! 

Avoid sudden starts, excessive speed 

and sudden stops. 

 

1. 

Release the parking brake. Move the throttle lever into the 

FAST 

 position.

2. 

To travel FORWARD, slowly press the drive pedal forward 

until the desired speed is achieved. See Figure 5-3.

Travel in Reverse

Travel Forward

Figure 5-3

3. 

To stop or slow down the tractor, take your foot off of the 

forward or reverse drive pedal. To lock the parking brake, 

pull the lever fully rearward and to the right; then into the 

short “J” slot to engage the brake. Pull the lever up out 

of the “J” slot and to the left; then completely forward to 

disengage the parking brake.

NOTE: 

The forward and reverse pedals must not be used when 

the brake is partially engaged. When the brake is locked in the 

“J” the drive belt is disengaged but if the brake is only part way 

back then the brakes are engaged but so is the drive belt so 

transmission damage will occur if you push forward or reverse.
4. 

To travel in REVERSE, check that the area behind is clear 

then slowly reverse pedal with the ball of your foot (NOT 

your heel) until the desired speed is achieved. See Figure 

5-3.

CAUTION: 

Do NOT attempt to change the 

direction of travel when the tractor is in motion. 

Always bring the tractor to a complete stop before 

moving the tractor from forward to reverse or vice 

versa.

WARNING! 

Do not leave the seat of the tractor 

without first placing the PTO/Blade Engage knob in 

the disengaged (OFF) position and engaging the 

parking brake. If leaving the tractor unattended, also 

turn the engine off and remove the ignition key.

Содержание Z-Force 48





































Отзывы: