Cub Cadet SERIES 5000 5252 Скачать руководство пользователя | Manualshive

Страница: 33 / 48

background image

33

Figure 42

•

Note the position of the two harness leads, then
disconnect the leads and replace the faulty
relay with a new relay. Secure the relay to the
wire harness with electrical tape.

•

Position the wire harness in the dash panel and
reinstall the dash panel insert.

CHECKING TRANSMISSION/HYDRAULIC
SYSTEM OIL LEVEL

Check the hydro transmission/hydraulic system oil
level before each use.

NOTE:

Check the oil level

only while the engine is stopped and the tractor is
standing on a level surface.

The oil level sight glass is located in the rear of the
transmission housing, just to the right of the rear
PTO shaft. Refer to Figure 43.

The oil level is okay if oil can be seen through the
sight glass. If the level is below the sight glass, oil
must be added to the transmission as follows:

•

Locate the oil fill plug on the upper right of the
rear of the transmission housing. See Figure 43.

Figure 43

•

Clean the area around the oil fill plug to prevent
debris from entering the transmission housing.

•

Turn the oil fill plug counterclockwise to unscrew
from the transmission housing.

•

Insert a funnel (preferably one with a flexible

spout) into the fill hole of the transmission
housing.

•

Add Cub Cadet Drive System Plus oil until the
oil level can be seen through the sight glass.
Do not overfill the transmission.

IMPORTANT:

Always use Cub Cadet Drive

System Plus oil to ensure correct formulation.
Substitute oils could affect performance and
may cause damage to the transmission.

•

Reinsert the oil fill plug into the transmission
housing and turn clockwise until tight.

CHANGING THE HYDRO TRANSMISSION AND
HYDRAULIC SYSTEM OIL FILTERS

With the exception of the first oil filter change after
the 25 hour break-in period, the

hydraulic system oil

filter

should be changed along with the

transmission/hydraulic system oil after every 200
hours of operation. The

hydro transmission filter

should be changed after every 100 hours of
operation.

25 Hour Break-In Period Filter Change

During the initial hours of tractor operation, contam-
inants caused by the normal break-in of internal
transmission and hydraulic system components will
collect in the oil filters. Because of this, both the
hydro transmission and hydraulic system filters
should be changed after the first 25 hours of
operation.

Hydro Pump Filter

— Part No. BS-492932S

Hydraulic System Filter

— Part No. 723-3014

NOTE:

If a front end loader, or a loader and back-

hoe, is installed on the tractor

after the first 25

hours

of operation, it is recommended that the fil-

ters again be changed after the first 25 hours of
operation with these attachments installed

.

Changing Hydro Transmission Oil Filter

The hydro transmission oil filter should be changed
after the first 25 of tractor operation, and after every
100 hours operation.

•

Stop the tractor engine and lower the mower
deck or any other hydraulically lifted implement
to the ground.

•

Slide the seat fully forward; then tilt seat forward.

FLASHER
RELAY

TAPE

HARNESS
LEADS

WIRE
HARNESS

OIL FILL PLUG

OIL LEVEL
SIGHT
HOLE

«
...
31
32
33
34
35
...
»

Содержание SERIES 5000 5252

















































Отзывы:

Нет отзывов

Похожие инструкции для SERIES 5000 5252

Бренд: Ransomes Страницы: 54

Бренд: Yard Machines Страницы: 44

Бренд: Yardworks Страницы: 21

Бренд: LawnBoss Страницы: 34

Бренд: Ransomes Страницы: 81

Бренд: MTD Страницы: 19

Бренд: Scag Power Equipment Страницы: 20

Бренд: Jacobsen Страницы: 76

Бренд: MTD Страницы: 8

Бренд: Weed Eater Страницы: 30

LX466 13AT61RH044

Бренд: Toro Страницы: 36

Бренд: Grizzly Страницы: 116

Бренд: Flymo Страницы: 12

Бренд: Simplicity Страницы: 4

Бренд: Simplicity Страницы: 15

Бренд: Simplicity Страницы: 40

Бренд: Simplicity Страницы: 24

Бренд: Simplicity Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды