background image

Domestic Compact Electrical Systems

 90

2.26. The circuits completed by the closing of the 

three sets of contacts in the Series 5000 domes-
tic compact are as follows: 

The red wire with black trace connects to the 
blue wire, sending power to the instrument panel 
(pin # 20) telling it that the brake is on.  This illu-
minates a “brake” lamp in the panel.

The starter circuit (orange wire with black trace) 
connects from the PTO switch (PTO OFF), 
through the brake switch contacts, to the orange 
wire with white trace that energizes the windings 
of the starter relay.  Energizing the starter relay 
passes power to the other orange and white wire 
on the relay, triggering the starter solenoid and 
motor.

The yellow wire gets power from the PTO switch 
when the PTO is off.  When the brakes are 
applied, the power passes to the red wire on the 
brake switch.  The red wire takes power to the 
after-fire solenoid.  

If this circuit is broken, the engine will stop       
from lack of fuel.

The seat switch feeds this circuit between the 
brake switch and the after-fire solenoid.  Either 
the seat most be occupied -or- the brake must 
be applied -and- the PTO must be off to keep the 
after-fire solenoid energized.

2.27. The Series 6000 and Series 7000 brake switch 

has two sets of contacts.  It is mounted to the 
right hand side frame channel, in front of the 
pedal linkages. See Figure 2.27.

2.28. The circuits completed by the closing of the 

three sets of contacts in the Series 5000 domes-
tic compact are as follows: 

The Starter circuit (orange wire with black trace) 
delivers power from PTO switch (PTO OFF) 
through the brake switch contacts, to the orange 
wire with white trace.  This sends power to trig-
ger the starter solenoid and to the instrument 
panel (pin # 20) telling it that the brake is on.  
This illuminates a “brake” lamp in the panel.

The yellow wire gets power from the PTO switch 
when the PTO is off.  When the brakes are 
applied, the power passes to the red wire on the 
brake switch.  The red wire takes power to the 
after-fire solenoid.  

If this circuit is broken, the engine will stop       
from lack of fuel.

The seat switch feeds this circuit between the 
brake switch and the after-fire solenoid.  Either 
the seat most be occupied -or- the brake must 
be applied -and- the PTO must be off to keep the 
after-fire solenoid energized.

3.

ELECTRIC CLUTCH AND FUEL PUMP

3.1.

The electric PTO clutch on the Series 6000 and 
domestic Series 7000 compact tractors is con-
tained inside the transaxle.  The wire that pro-
vides power to it enters the transaxle housing 
through a notch in the top edge of the right side 
of the housing. See Figure 3.1.

Figure 2.27

Brake switch:
Series 6000 and 7000

Figure 3.1

Electrical connection
for PTO

www.mymowerparts.com

K&T Saw Shop 606-678-9623 or 606-561-4983

Содержание Domestic Series 5000

































































































Отзывы: