Cub Cadet CSV240 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

9

SECTION 5: ADJUSTING YOUR CHIPPER SHREDDER VACUUM

WARNING: Do not at any time make any
adjustments without first stopping engine,
disconnecting spark plug wire, and
grounding it against the engine.

Front Caster Wheels

This chipper shredder vacuum is equipped with front
caster wheels. The casters can be locked in a straight
ahead position or position to swivel freely. Lift and place
pins in the larger holes for locked or straight ahead
operation. Place pins in smaller holes to allow casters
to rotate freely. Lock wheels in straight position when
operating on slopes. See Figure 7.

Figure 7

Nozzle Door Height Adjustment

The nozzle adjustment levers are located on each side
of the nozzle door. The nozzle door can be adjusted to
any of five positions, ranging from 1/2” to 3” ground
clearance that will provide the best performance for the
operating conditions. Slide the height adjustment lever
forward or backward for adjusting the nozzle door
upwards or downwards. Height must be adjusted
equally. In general, raise the nozzle to vacuum a thick
layer of leaves and lower the nozzle for smooth
surfaces. See Figure 8.

Figure 8

Drive Clutch Cable Adjustment

Adjust the drive clutch control if the chipper shredder
vacuum moves forward with the drive clutch control
disengaged, if it does not self-propel with the drive
clutch control engaged, or if drive belt is slipping (unit
hesitates while engine maintains the same speed). Use
the adjustment wheel located in the clutch control
housing to tighten or loosen the clutch cable. In
addition, the adjustment wheel may also be used to
determine the position in which the drive clutch control
is engaged. If it is more comfortable to have the drive
engaged with the lever further away from the handle,
tighten the clutch cable. See Figure 9.

Figure 9

Engine Adjustments

Refer to the separate engine manual for engine
adjustment instructions.

Smaller Hole
(Rotate Freely)

Larger Hole
(Locked)

Nozzle Door
Adjustment
Lever

Tighten

Loosen

Adjustment
Wheel

«
...
7
8
9
10
11
...
»

Содержание CSV240

























Отзывы:

Нет отзывов

Похожие инструкции для CSV240

Бренд: MBM Страницы: 29

Бренд: Morrison Страницы: 8

Бренд: UNITED OFFICE Страницы: 28

Бренд: Cub Cadet Страницы: 24

Бренд: 5Star Systems Страницы: 29

Бренд: Rexel Страницы: 31

Бренд: Q-Connect Страницы: 17

Models with electric motors

Бренд: Patriot Страницы: 22

Бренд: Jet Страницы: 12

Powershred P-57Cs

Бренд: Fellowes Страницы: 2

Powershred C-220

Бренд: Fellowes Страницы: 2

Microshred MS-450Cs

Бренд: Fellowes Страницы: 8

Microshred MS-450Cs

Бренд: Fellowes Страницы: 6

Бренд: Fellowes Страницы: 8

Бренд: EMAK Страницы: 38

Бренд: GardenBeaut Страницы: 20

Бренд: Jet Страницы: 12

Shredding TruckLoader 8160

Бренд: Little Wonder Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды