manualshive.com logo in svg

Cub Cadet 524 SWE, Руководство оператора

Поделиться
Скачать
Cub Cadet 524 SWE Скачать руководство пользователя страница 30

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB) 

and the United States Environment Protection Agency (U. S. EPA) 

Emission Control System Warranty Statement 

(Owner’s Defect Warranty Rights and Obligations)

EMISSION CONTROL SYSTEM COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 2005 AND THERE-
AFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 2005 AND LATER ENGINES WHICH ARE PURCHASED AND 
USED ELSEWHERE IN THE UNITED STATES.
                                                       California and elsewhere in the United States Emission Control Defects Warranty Coverage
The California Air Resources Board (CARB), U. S. EPA and MTD are pleased to explain the emissions control system warranty on your model year 
2006 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the States anti-smog 
standards. Elsewhere in the United States, new non-road, spark-ignition engines certified for model 2005 and later, must meet similar standards set 
forth by the U. S. EPA. MTD must warranty the emission control system on your engine for the period of time listed below, provided there has been 
no abuse, neglect or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, and catalytic converter, fuel tanks, 
fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.
Where a warrantable condition exists, MTD will repair your small off-road engine at no cost to your including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This emissions control system is warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or 
replaced by MTD.

OWNER’S WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. MTD 
recommends that you retain all your receipts covering maintenances on your small off-road engine, but MTD can not deny warranty solely for the 
lack of receipts or for your failure to ensure the performance to all scheduled maintenance.
As the small off-road engine owner, you should however be aware that MTD may deny your warranty coverage if your small off-road engine or part 
has failed due to abuse, neglect, improper maintenance or unapproved modifications. 
You are responsible for presenting your small off-road engine to an Authorized MTD Service Dealer as soon as a problem exists. The warranted 
repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a MTD Service Representative at 1-800-800-7310 
and address is MTD CONSUMER GROUP, P.O. Box 361131, Cleveland OH, 44136-0019.

DEFECTS WARRANTY REqUIREMENTS FOR 1995 AND LATER SMALL OFF-ROAD ENGINES:

This section applies to 1995 and later small off-road engines. The warranty period begins on the date the engine or equipment is delivered to an 
ultimate purchaser.
   

 

 

 

 

        (a) General Emissions Warranty Coverage

MTD must warrant to the ultimate purchaser and each subsequent purchaser that the engine is:
  (1) Designed, built, and equipped so as to conform with all applicable regulations adopted by the Air Resources Board pursuant to its authority in 

Chapters 1 and 2,Part 5, Division 26 of the Health and Safety Code; and

  (2) Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to the part as 

described in the engine manufacturer’s application for certification for a period of two years.

   

 

 

 

(b) The warranty on emissions-related parts will be interpreted as follows:

  (1) Any warranted part that is not scheduled for replacement as required maintenance in the written instructions required by Subsection (c) 

must be warranted for the warranty period defined in Subsection (a)(2). If any such part fails during the period of warranty coverage, it must be 
repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under the warranty must be warranted for 
the remaining warranty period.

  (2) Any warranted part that is scheduled only for regular inspection in the written instructions required by Subsection (c) must be warranted for 

the warranty period defined in Subsection (a)(2). A statement in such written instructions to the effect of “repair or replace as necessary” will 
not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for the remaining warranty 
period.

  (3) Any warranted part that which is scheduled for replacement as required maintenance in the written instructions required by Subsection (c) 

must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled 
replacement, the part must be repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under 
warranty must be warranted for the remainder of the period prior to the first scheduled replacement point for the part.

Содержание 524 SWE

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды